ZRT6510WW Amana Range - Instructions

I called the local appliance parts store and they said it would cost $60-80 and take a week to order. I paid $16 and received my rack in 2 days!

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Removed old assembly, attached wires to new and inserted into space for same. Of course you must turn off the range circuit breaker. The part that took the most time was removing the old assembly. Once that was done, the rest took only a few minutes.

I was surprised when I was able to find that the (10 year old) parts for one of the drawer slides of my stove were still available. However, I was disappointed that the small bolt that I ordered did not come with a nut. I was lucky to find one in a collection of nuts in my workshop, and so was able to fix the slide. However, I suggest that if you supply someone with a bolt, that you include the nut that is necessary to make it work.

I turned off the breaker and unscrewed the element. Removed the plug connection and once I got the correct part, we plugged it in, screwed it back into the oven wall and done! I am a single female and was able to replace the heating element in a short amount of time with assistance from my 16 year old son!! I was very surprised at how easy it was to repair. The key is to get the correct part the 1st time!

Very easy fix. This is done through the oven door. Don't pull it out or do anything exotic. Turn the breaker off. Don't skip this Since you're dealing with 220v here. Shine a bright light into the back of the oven to identify the element attachment screws. Use a number 2 Phillips to remove the 2 screws holding the element in place. Pull the element straight out. This may require a bit of manipulation wiggling back an forth. Don't yank to hard. There was probably 6" of free wire. Next free the wires attached via spade terminals from the old element. Putt the new element in place and reattach the wires. Carefully push wires back thru the holes and secure with the screws. Reset the breaker and turn it on. Totally simple. My oven was 18 years old and the screws came right out. I expected difficulty but none encountered.

Remove three strews and two wires. Less than fifteen minutes for this Seventy Seven year old farm boy!

First, I unplugged the power cord from the receptacle. I then removed two philiphead screws that hold the element in place. I the pulled the element out about an inch and a half . I then disconnected the the two wires from the element. The I connected the replacement element and resecured it with the two mounting screws. I assured everything was correct and then I plugged in the power cord and turned the oven on low heat to give it a test. Everything workout just great. The part was just what I needed.

Removed two screws securing heating element. Removed broken element and disconnected wires. Removed back panel of oven, unplugged from outlet, installed new element, attaching 2 screws. From back side of oven reattached 2 wires, replaced back panel and plugged in. Pretty simple!

had to slide the range out from the wall and pull the electrical plug, then using a nut driver ,I removed 9 screws from the back panel and removed the back panel to expose the bake element wiring, had to remove the three wires connecting the power cord to the range terminals a/c the back panel would not fully come off with these wires connected. i then pulled the 2 stake eyes from the element, unscrewed the 2 screws
securing the bake element from inside the stove and removed the element, re-installed the new element and screwed into place, attached the
stake eyes on the rear of the element and re-attached the power cord, put the back cover back on and plugged the range in., tested and the range functioned as intended.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Plug the wires onto the new bake element and re-screw back into place.

first removed 3 screws in front of the range then lift up the top glass and removed 1 screw that is holding the element and then disconnect the wires that are connect on the element then put the new element on place and wired it test it and works good

It was simple. I flipped the circuit breaker just in case, and then unscrewed the bracket for the old heatng element. Disconnected the two plugs, connected the plugs for the new element, and screwed the new bracket back in.
The saleslady assured me when I was purchasing it from PartSelect that it was pretty easy. That gave me the confidence, and she was telling the truth. I will purchase again from Part Select....although I hope I won't have to do so for a while.

removed 2 screws holding top in place witch gave me ac access to none working part. removed 5 screws witch let me remove part, reversed order to reinstall part, very easy
Donald Carpenter

Unscrewed all the phillips screws holding the door together. Re-assembly indicates that you want to note exactly how the sides overlap the front and back steel panels, possibly take a cellphone picture before starting. The front and back panel will bend down the bottom attachment metal tabs, misaligning the sides, etc if you replace the glass with the door still on the range. Prob. best to have a second standing by or remove entire door first.