ZISB360DMA General Electric Refrigerator - Instructions

I identified the noise was coming from the coils / and the fan. Cleaning the fan helped reduce the noise a bit but it still kept recurring. I ordered the part, which was really easy using the diagram on the website. The instructions and the video were really helpful and was able to remove the old motor and replace it with the new one with relative ease. While there I cleaned the fan blade and vacuumed the surrounding area. This whole repair went quite smoothly and has given me the confidence to take on other repairs before calling out the repairman.

Slip the front cover off by gently pulling down, carefully un-plug the wire connectors (x3), remove 4 screws and remove paddle assembly. 2 screws hold the flap on and 3 hold the solenoid. Replace the screws with stainless so they won't rust. I tried coating the solenoid in lithum grease to prevent rust, onlt time will tell if it works.

I just follow to the video and take step by step. It's was very helpful and easy. Thank you.

Removed the Control Panel and the outside of the Dispenser Outlet. Removed the Flapper Door and the solenoid. Replaced both parts with new parts, and re-assembled. The pin, at the top of the Solenoid was badly worn and the plastic arm was very rough on the surface adjacent to the worn pin.

I followed the video provided by PartSelect, very helpful. I had to cut and splice 4 wires. The repair was successful. The replacement part was an exact duplicate of the original. I still notice the same sound but one tenth the volume. I hope the problem does not return. Many thanks to PartSelect for information to identify the problem and prompt shipping of the repair part.

Turned the water off to the refrigerator. Pulled the refrigerator away from the wall opening. Removed the back lower panel. Removed the lines to the water valve. Removed the electrical connections. Installed the water lines on the new valve and verified they would not pull out of the push in connections. Installed the electrical connections. Turned the water on and checked for leaks and proper operation. Reinstalled the back panel and positioned the refrigerator in it's proper position.

Removed control panel by inserting small screwdriver in the 3 holes underneath to loosen. Remove 4 screws holding circuit board . Unplugged 3 connectors. Removing circuit board gave access to flapper. Removed flapper by unclipping. Installed new flapper and reversed disassembly procedure. This was 2nd time in 2 years I had to replace this part.

After recieving the water pump and ice maker repair kit,i had my laptop on the counter. Your video of Steve the repair man made the job extreamly easy. Your concept of ordering and repairing is awesome! Thanks.

Ice maker was side mount instead of rear mount as shown in previous insructions. Removed one screw and slide ice maker forward. used flat head screw driver to undo the ice maker plug. The ice maker came right out. Removed old ice maker fill cup and put it on the new ice maker. Slide the new ice maker into place and used the same screw to secure it. Pluged it in and turned on the ice maker. Had new ice in a couple of hours. It comes with a round plug to square plug adapter, new fill cup and fill tube, all of which I didn't use.

Only needed to remove one screw, slide unit out and disconnect the power cord. Theb reverse the above operation to install the replace ice maker unit. Quick and extremely easy....

Had to remove all the covers and fans to expose the condenser, which was difficult as the parts were frozen to it. The styrofoam covering the condenser made it almost impossible to defrost it. Therefore, I ripped the styrofoam off to expose the condenser. Was not really difficult to fix the styrofoam cover using metal tape. Replaced temperature sensor in aluminum block, and used butyl sealant to secure. Had to also re-install parts of ice-ball kit that were not well covered. Lots of parts to keep track of, but anyone could do it.

took 1 screw out and removed ice maker and slid new one in and replace screw and connected power cord

Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH