YWMH53520AH0 Whirlpool Microwave - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Put the Fuse in, then plugged it in came on for a min then everything went out!!!!!
Took the front off and behind a plate was the fuse, so I replaced it for what good that did!!!
Parts Used:
-
Stephen from SPRINGFIELD, WV
-
Difficulty Level:Very Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
4 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The glass tray in the microwave got chipped while i was washing it and started to crack.
-
Amber from Loretto, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Replacement
-
George from Statham, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
changed filters
-
Edward from Oakland, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken plate
Took the replacement plate out of the box and put it in the microwave in seconds. I never realized how much of a difference having the correct microwave plate would make. It's great to have it back.
Parts Used:
-
JASON from ABSECON, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
replace filter
-
Barbara from Cranston, RI
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Bulb burned out
You had alerted that it was imperative to unplug unit before starting to remove defective bulb. As described, there was silicon on bulb and socket and bulb broke upon my attempt to remove. Had to use needle nose pliers to get metal base of old bulb from socket, then all went well.
Parts Used:
-
Lester from Mesquite, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Burn't out bulb.
-
Carter from McCordsville, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Clearing the clean code was the hardest part.
I had no problem installing the new filter. Just used a phillips screw driver to remove the two screws holding the vent cover in place. Cleaned the dust out of the ducts and reinstalled the new filter. The screws must be held to the screw driver with your finger tips so you don't drop them in the vent cover. The most difficulty I had was in clearing the clean code from the screen. There are no instructions in the owners manual for doing this. But after several tries I got it.
Parts Used:
-
Wayne from New Berlin, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Filter dirty
I unscrewed the filter cover, replaced the charcoal filter and replace the cover. The other wire mesh filter slides right into place. You sent me the right parts for my filter replacement on my microwave. Easy install. Thanks
Parts Used:
-
John from Denver, CO
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
left something in microwave too long and burned parts
-
Norman from Angier, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
burnt out light bulb
The problem I have with changing the bulb is my microwave is an overhead one and therefore I cannot tip it on its side to easily replace the bulb. I have to drop the lid down and carefully install the new bulb from underneath.
Parts Used:
-
Shirley from Londonderry, NH
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
rotating glass dish assembly making stange noise
The lady in the Nova Scotia call center should get all the credit for being able to identify the part I needed from only the very limited information I was able to give her. Employee of the month for her. She also had such a great can do attitude. Lawence Baier
Parts Used:
-
Lawrence from Excelsior, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Broke a 15 year old glass cooking tray
Ordered the item on a Monday at 12pm and it arrived the next day. Amazing!
Parts Used:
-
Stephanie from La Jolla, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
glass cooking tray droped and broken
-
janice from dunn, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!