All Installation Instructions for Whirlpool Microwave YMH2175XSQ2

Foreclosed home: parts were missing

Having the correct model number helps:
Just place the parts in the microwave and it worked.

Parts Used:

RING-TURN

Glass Cooking Tray

OLIV from OAKLEY, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burnt Out Light Bulb Replacement

Open compartment, installed bulb, closed compartment

Parts Used:

Light Bulb - 40W

alfred from summerville, SC
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

9 of 30 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Put the Fuse in, then plugged it in came on for a min then everything went out!!!!!

Took the front off and behind a plate was the fuse, so I replaced it for what good that did!!!

Parts Used:

R CERAMIC FUSE,20A/250V,MHC

Stephen from SPRINGFIELD, WV
Difficulty Level:
Very Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers

4 of 16 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Microwave turntable stopped rotating.

1. Unplug the power cord from the wall socket. 2. Remove the 10 screws holding the bottom cabinet cover in place. The bottom cabinet cover will swing down allowing acces to the inside ofe the microwave. 3. Remove the connector from the turntable motor. 4. Use a T15 Torx driver to remove the 2 Torx screws holding the motor in place. 5. Remove the motor. 6. Reverse the process using the new motor.

Parts Used:

MOTOR-TURN

Larrt from Minooka, IL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

replace light blub

removed grill cover, removed bulb plate, unscrew bulb, screw new bulb in socket,put bulb cover back on and screw grill cover back on. no issues whatsoever.

Parts Used:

Light Bulb - 40W

roger from palm coast, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Glass cooking tray for microwave cracked.

All I had to do was lay the new tray in the microwave. Easy as pie. Also, the new tray arrived very quickly.

Parts Used:

Glass Cooking Tray

Sharon from Kannapolis, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

The star broke when trying to loosen the bolt at the top

I had to hammer out the broken star wrench tip then progressively drill the head off of the bolt. Once accomplished I could remove the door. I used a standard replacement screw I case I ever have to replace the door again. The manufacturer should use a fastener other than a star head bolt.

Parts Used:

Complete Door Assembly - White

JOHN from Marana, AZ
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours

Was this instruction helpful to you?

Thank you for voting!

Missing bracket for mounting microwave oven

Attached bracket to wall with screws and hung microwave oven. Very easy project.

Parts Used:

Mounting Bracket

Timothy from Reno, NV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Needed a clean filter

Stood on a step stool (microwave over stove), took off the one panel,removed old filter and put in new one

Parts Used:

Charcoal Filter

Ethel from New Berlin, WI
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Broke glass tray

Arrived in 24hours!!! Great.

Parts Used:

Glass Cooking Tray

Katherine from Cleveland, TN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Reminder signal and message to change filter on microwave digital display.

Removed 2 screws on the top of the microwave and removed top/front piece of microwave. Slid out old filter (which didn't look dirty at all) and replaced it with the new one. Replaced top/front piece and 2 screws. It took less than 5 minutes.

Parts Used:

Charcoal Filter

Susan from North Olmsted, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

broken screw holes

unscrewed the screws and put the new vent in

Parts Used:

Vent Grille - White

Tom from Volo, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Dryer Stopped Drying Completely, Timer Didn't Shut It Off.

1. Safely unplug the dryer. 2. Unconnect the vent hose. 3. Pull it out so you can have room to move around to work on it. I actually in a power chair so I put an old blanket on the floor and laid it face down to work on it. It was extremely dirty so I used a shop vac to clean off the back panel before starting. 4. I took off all the screws and cord cover with a nut driver, used the shop vac again to clean the entire inside. Properly a 1/2 to 1 inch of dust and lint was built up causing a dangerous fire situation for sure. Once clean, take a photos especially of where the electrical connection are. 5 Located and removed the two screws holding the element on, used a nut driver and long nose pliers to remove the heat sensor & electrical connections. 6. Dry fit the element before tightening screws to make sure placement is correct then match the holes replace the screws. 7. Using the photos put the heat sensor & electrial wires back on, you may need to use the pliers to push it on tight. Double check everything, clean back panel inside and out, match up holes replace screws, I actually checked my power cords screws for tightness then replaced cord cover. 8. Replace vent hose if needed or then reattach it and plug it up. You may need to check the dryer barrel by turning the drum around a few times. Should work perfect, you will smell the element a little but it should be ok. Remember clean your dryer inside and out every six months or so to prevent dryer fires.

Parts Used: