Models > YMED5800TW0 > Instructions

YMED5800TW0 Maytag Dryer - Instructions

All Instructions for the YMED5800TW0
1186 - 1192 of 1192
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
no heat
replacer upper heat themo
Parts Used:
Thermal Cut-Off Kit
  • kenneth from new madison, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer tub drive belt broke
Unplugged the power cord. Removed two screws on lint vent , used putty knife to release clips to raise top at front of unit. Disconnected the plug from front door switch. Laid dryer on its back. Removed two screws to remove front including the door. Vacuumed lint from inside unit. Installed belt temporarily using two pieces of masking tape to hold it in place while properly routing the belt. Gave the tub a full turn to insure alignment.. Reinstalled the front of unit with the two screws. Righted the unit and snapped down the top. Replaced the two lint vent screws. Plugged it back in and done! Piece of cake!
Parts Used:
Multi Rib Belt - 92-1/4"
  • Ray from Salisbury, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Washer overflowed
Once I watched a YouTube video showing me how to do the job I ordered the part from you. Am so impressed with your fast shipping and best prices via the Internet. Thank you SO much! The water level switch was easy to install, it ws getting the cover on the washer back on that was hard for me since I am 68 yrs old and have a bad knee. Its why it took me two hours to do what most people could do in 20 minutes.
Parts Used:
Leveling Foot
  • Beth from Valley Springs, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
no heat
I unplugged the dyer remove the back and took out the part and replaced it with the new one done !Thanks to your video I watch on the enternet.thank you so much
Parts Used:
Thermal Cut-Off Kit
  • Anna from Travelers Rest, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Noisy tumbler & worn lint trap seal
Followed procedures in Parts Select web site video
Parts Used:
Rear Drum Support Roller Kit Lint Trap Housing Seal
  • Pedro from Brunswick, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer would not shut down when door is opened.
Follow your instructions. Thank You
Parts Used:
Dryer Door Switch
  • Robert from Garden Grove, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
couldn't get the wire connection anywhere after we bought the heating element.
we received the two heating element wires in 3 days and connected the heating element with no problem works great.
Parts Used:
Heating Element Connection Wire Kit
  • Betty from Erie, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the YMED5800TW0
1186 - 1192 of 1192
Back to Top