YMED5720TQ1 Dryer - Instructions

After reviewing a variety of online instructional videos I was able to figure out how to remove the top ("hood") panel of dryer to access the door switch. Once I had access the switch was relatively simple to replace.

I am a female, not a handy man. But by following the repair man on the video, it was easy. I also went ahead and installed the maintance kit. The maintance kit was recommended when I ordered the parts. I followed by maintaining the washer.

I just followed the instructions on the video. The only helpful addition I have...make sure the power is off before you start. I did get that point when the video said to turn the power back on, at the end of the video. In all...a great experience and I saved more than $200.00 doing it myself, with the help of the FANTASTIC web site at PartSelect!

Watched the repair video once, it was real informative and easy to follow. The repair took about 30 minutes to complete. The video went step by step. Had no problems what so ever. Made the reapir and turned the dryer on and let it run for a few minutes and once again had all the heat I needed to make it operate correctley. I recomend that once you see your dryer is not dring your clothes like it once did, replace these parts. I let this go on for a year thinking my wife was putting way to many clothes in the dryer. It was not that at all. No telling how much money we could have saved on our electric bill by replacing these parts sooner. $30 dollars for the parts, I bet we spent that much a week on extra drying cycles. What used to take 2-3 cycles to dry now only takes one cycle. Runs just like it did when we purchased it.I will buy from this site again, easy to use all the information you need to make the repair and prompt shipping. Awesome site.

I follow the instructions from the video sent to me with the email to tell me my new belt was shipped. Made the whole job go a easy as could be. Parts Select made fixing my dryer so simple and I also got the belt within 2 days. I recommend buying parts only from you! Glenn

took out the fabric softener cup pull out diaphram unscrewed the bolt pull out the cup replaced with new parts I want to thank you for your fast service. it is awesome. i will recommend you to all my friends.

remove 2 screws from lint vent, use putty knife to remove top op dryer, remove 2 screws holding switch.

After I received the new belt I un-plugged the electric cord and shut off the gas supply. I pulled the dryer about 10 inches away from the wall to remove the vent duct from the back of the dryer. Used the putty knife to release the clips on bottom front panel and a screw driver to pop the front of the top at the left side and right side, removed the two Phillips head screws under the lint door, then lifted the top to the vertical position. Loosened the hex head screws at the bottom of the upper front panel (don't take them out). At the top back side of the front panel, pull off the electrical wires from the door interlock switch and pull the retainer holding the wires to the front panel (don't take the plastic clip from the wires.) Place some wood blocks to support the drum at the front of the drum. Use the nut driver to remove the two screws on the inside at the top of the front panel. Disconnect the two springs that hold the door closed. Lift the panel from the two loosened nuts at the bottom and pull it away from the drum and let the drum settle on the blocks of wood to support it. Place the new belt around the drum lining it up where the old belt left its mark around the drum with the grooved surface facing the drum. Replace the front upper panel with the door to engage to two tabs on the screws you left at the bottom. Lift the drum so that it engages with the opening in the front panel. In case where the drum had dropped too far, use the putty knife to engage the felt flange at the rear of the drum with the rear cabinet flange. Reinstall the two screws at the top that you had removed. Reconnect the two wires at the interlock switch and snap the clip with the wires to the flange of the upper front panel. Replace the door springs on the hinge extensions to the flange at the bottom of the cabinet. Set the Idler pulley assembly into the cabinet floor sliding the end tab into the slot and the two tabs fit into the holes in the floor. Pull a loop of the belt under the idler pulley and then pull it toward the motor pulley. You might use the shaft of your Phillips screw driver instead of you fingers to get it around the pulley on the motor shaft. Turn the drum by had for several complete turns to ensure that the belt lines up on the drum and that the drum isn't binding on the back or front seals. Close the top, snapping onto the top of the cabinet. Plug the dryer into the electric outlet and set the timer to Fluff Air range and push the start button with the door closed. The drum should be turning smoothly. Open the door and all should stop. Reconnect the Vent and move the dryer back to its former position. Turn gas supply on but do not start the dryer. Check for gas leaks. If you find a leak in either at connectors or the flexible connecter call a qualified contractor to replace the flex connecter. Otherwise you can then set for one of the dryer settings and push the start button and observe the burner through the lower panel to see that the igniter is lighting up and finally the gas turns on and a decent blue flam is burning in the combustion tube. Open the dryer door and the flame should cut off and the drum stop turning. You are ready to set the bottom panel. Set the panel on the two lower tabs and close it upward until the snaps lock it in position. Job Done

Diagnose the problem. Is it the motor ? Is it the belt ? Order the correct repair kit, use name brand parts to ensure reliability. READ THE SUPPLIED DIRECTIONS. You can use a small wood shim or wedge at the top front corners to open the top . Use a 5/16" socket to remove the 2 screws at the top outside corners. Lift the front panel straight up, supporting the drum as you lift it off. Remove the drum, taking it straight out the front. Install the new drum rollers, install the idler, and then the belt around the drum. Install the drum on the rear rollers, make sure the seal is not folded under. Push the drum back against the seal flange, support the front of the drum with your right (or left ) hand, and sit the front panel on the lower pins, and gently push the front panel to the sidewalls. Feed the belt through the idler and around the motor pulley. This job is easily performed in about 20 minutes. Clean the interior while replacing the belt/idler and drum rollers. With the top lifted, after assembly, test run the dryer to make sure there are no "funny noises" after the repair. Watch especially for the white rub strips on the front edge of the drum. They tend to fold over when attaching the front panel. Job done !

Remove and replace timer

unpluged dryer from wall,lifted top of dryer unpluged door switch took out two screws that hold switch, installeed new switch, put top of dryer down, plugged dryer back into wall, very easy repair.

remove top &replace switch

Watched repair video first to access problems and steps to do replacement for parts. Took more than :30 only because most of the time was spent cleaning. Amazing how much dirt and dust accumlates inside a closed unit. Even took the back off to clean and check electrical connections. Parts were exactly as shown and explained. Would absolutely use PartSelect again if needed.

Verified that the heater element was working; drum and contents were getting hot. Could hear the thermostat clicking on/off as the element started to glow. Drum stayed very steamy the entire time; consistent with no airflow. Fan motor was running, dryer vent/line were clear. Verified cold (not hot) air from the external vent. Seals had degraded to the point that the fan was not drawing air from the drum, but from inside the dryer cabinet at the lower seal (by the fan blades); hot air was escaping from the upper seal and was causing the dryer cabinet to get unusually hot. Installed these 2 seals, and the dryer is working perfectly now.

TURN OFF POWER TO DRYER............................. Pay attention to where everything is as you take it apart, so it can be put back the same way. Take out the two screws by the lint screen. Use flat tip screwdriver between space in front of top to help lift top. Use rag on tip of screwdriver so as not to scratch it. Take out two screws inside the front panel at the top. One on each side. Unhook the switch wiring. Lift up the front panel to take off. The tub will be loose, so it can be taken out to inspect other components. Some call the tub a drum. Be sure to see how the belt tensioner is attached, so it can be put back on the same way, if it comes loose. It is under the tub. Take out old belt. Put new belt around tub. Make sure the tub sets on the two rollers in the back of dryer. While holding tub, put the belt around the grooved pulley on the motor. Grooves are face down against the tub. Feed belt through the tensioner. Put the bottom of front in on the tabs. Be sure belt is still in place around pulley and tensioner etc. Hold tub through front door and close front. Put the two screws back in on each side. Close top and put the two screws in at the lint screen. Done. Turn power back on. Turn on dryer to see if it operates properly. If not, check out your repair to see if everything is connected properly.