YKIRS608BSS0 KitchenAid Range - Instructions

the hardest part was moving stove to trplace part

Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place

It was easy to remove the old oven door gasket. Just a little tug was all that was needed. Installing new gasket was just as simple as tucking in the gasket end into the hole at the bottom and pushing the clip in the corresponding hole.
TIP: roll the end of the gasket and feed into the hole then use a small tipped screw driver or the point of a needle nose plier to finish installing the ends into the hole at the bottom of the door opening.

Replaced the safety thermostat and disconnected the oven light.
Works great again...without the light

Took out 2 screws took old one out an put new one in it even came with a heating element to replace which was sooo very nice! I had very good service from ordering to receiving! Everyone was very nice I will deal with this company again!

Very easy. Pulled the stove away from the wall. Used a screw driver to remove the two nuts to release the heat sensor, disconnected the wire, removed the sensor. Inserted the new sensor, plugged back into the circuit. put the two nuts back.
Beware, if the first time you put the oven on, if the error message comes back up (mine did) push the cancel/off button, wait a few minutes, put oven back on. System probably needed to reset. Mine worked perfectly after.

I read the help section and it said that the element was likely to be the problem (84%) and the fuse had a 14% chance to be the problem so I purchased both. After watching the video I tried the element first and that's what it was so I returned the fuse, Thanks for the help and video.

The company said it would cost me $698 to repair. I had a 2 year warranty and that was 2 months out of date.

Again thanks for the help.

Watch the video...

Very easy followed instructions from a youtube video.

The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.

Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564

Watched the video and realized this was something I could do myself...bear in mind I'm not exactly a handyman! Took me about 30min as the oven also needed some cleaning...my tenant definitely needs to use the self-cleaning!

I have to note, although the heating element was covered by Maytag's 10yr limited parts warranty, I decided to purchase from PartSelect since Maytag could not provide a ship date and I couldn't keep my tenant waiting! Supposedly Maytag had the part in stock but their warehouse was behind because of the pandemic...what a lame excuse! Almost a month later, Maytag has yet to ship the part! Needless to say, am very disappointed in Maytag's after sales and warranty program! I get the impression, they just wanted to pressure me to buy the new part!

Lastly, was very pleased and impressed by PartSelect's customer service! Their website was very easy to use, less expensive than buying direct from Maytag and the part was shipped same day! Thank you PartSelect!

I first shut off the breaker, then, after pulling the stove away from the wall, I unplugged it. I removed the two screws in the back of the stove which came off easily. I removed the two screws inside the oven and removed the bottom plate. I noticed the heating element I was changing had braces along the bottom. I had to remove the two screws and removed the burnt out element. The new element did not have the braces the original element had, but it fit in perfectly. Then I replaced all the screws, plugged it in and turned on the breaker and it worked. The only thing that we noticed is there’s a clicking sound every time the temperature increases. Not sure what that is.

Shut beaker off
Unhooked wires on element back of stove
Removed all racks
Unscrewed lower plate cover
Removed element
Inserted new element
Rebooked wires to element
Reinstalled cover plate
Turned breaker back on
Turned range on and let heat up
Turned it off
Reinstalled racks

Unplugged stove-Removed oven door two screws held the oven bottom pan removed same to observe the element removed thre fasteners removed inspection cover on back of the oven pulled off two electric wires replaced element reassembled easy job