Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
replace inner glass Jenn air range
Hired a pro. Parts are difficult to get on a timely basis today , if at all. Screw up this repair by damaging the outer " black glass " and you buy a new stove. It took three weeks to get my replacement glass even though PS said the part was being sent within a day of the order. Even so , I am am happy to have gotten it , and will continue to use the company.
Oven stopped heating, error message stated heating element
Very easy. Pulled the stove away from the wall. Used a screw driver to remove the two nuts to release the heat sensor, disconnected the wire, removed the sensor. Inserted the new sensor, plugged back into the circuit. put the two nuts back. Beware, if the first time you put the oven on, if the error message comes back up (mine did) push the cancel/off button, wait a few minutes, put oven back on. System probably needed to reset. Mine worked perfectly after.
It was easy to remove the old oven door gasket. Just a little tug was all that was needed. Installing new gasket was just as simple as tucking in the gasket end into the hole at the bottom and pushing the clip in the corresponding hole. TIP: roll the end of the gasket and feed into the hole then use a small tipped screw driver or the point of a needle nose plier to finish installing the ends into the hole at the bottom of the door opening.
Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place
First things first...Unplug the unit...Then remove the center plate from the back of the oven (one screw) and take clips off element. Then on the inside, there are 2 screws near the back on the bottom panel. These were rusted on pretty good, so that's where the vice grips came into play. The entire job would've gone much faster, if I wasn't fighting with these 2 screws...After you remove the screws, tilt up bottom panel and remove. Then you just remove 1 rear screw & 2 bottom screws and slide out the old element. Slide the new one in, secure it with the screws and screw the bottom panel back into place. Go to the rear of the oven, slide the 2 clips on the element and screw rear plate back on. Plug the oven back in and that's it...
First I removed the oven door, then I removed the three screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I connected the two wires to the new element , replaced the three holding screws and the oven door. ------END-------
The bake element in this oven is covered by a tray but after locating the screws for that and removing I could see the element was burnt so I just removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) then just reversed the procedure to install. Don't forget to unplug the unit first.
lower baking element was fried and no longer worked
Turn of power to the range. The element lies beneath a metal cover. The cover is held down by two screws in each of the back cornors. The burner element is held by a screw in the the back and by two screws near the front. Replacing the element was a snap. With the screws removed, pull on the element until the connecting wires are exposed. Pull the wires from the element and attatch to new element. Replace screws, cover etc. Turn on power and note the time it takes to reach a preset temp. You may detect a slight oder form a coating on the new element. .
First of all, let me say how "Not Handy" I am when it comes to these things. I decided to give this part a try after my oven decided to fail on Thanksgiving Day, so I ordered the part. It arrived on time as promised and packaged very well. The on-line parts breakout and testimony from the other buyers were so helpful. I had our oven back up and running in less than 10 minutes.
One thing I would also recommend is that you burn the element once installed for at least 15 minutes to get the newness smell off of it and then it won't permeate your food items.
Thanks, Parts Select! You saved me over $900.00; the price it was going to cost me to buy a new oven. :)
removed the two screws in the rear of the oven to access the element. once exposed I removed the four screws holding the element in place. Went to the ouitside back of the stove and removed one screw holding the shield to access the terminals for the element. Installation was in reverse order.
Pull oven away from wall and unplug. with the oven door open, remove 2 rear screws holding down the element cover and pull element cover out of the oven. remove 2 screws holding element down to the bottom of the stove, and one screw holding the back of the element to the rear. now go behind the oven and remove the access plate to the element power connection (one screw). Disconnect the 2 element power wires. remove element. to install, reverse these instructions
the oven door would not shut all the way, so heat was leaking
The part fit perfectly.Ther repair was logic. The door was of course heavy . I needed an extra hand. I would have appreciated of instructions were included with the part. Also a web link on how to do it would alos have helped greatly
