Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Clothes would not fully dry in automatic cycle
1st gen whirlpool Duet dryer sensor not working in automatic cycle. After ordering the moisture sensor harness which is about 6-8 inches long, I removed the lower panel and it is right there. I disconnected the two wire connectors in the upper left and I need a small screwdriver to disconnect the two pin connector which was a bit of a pain but once replaced I no longer had to use the timed setting to dry clothes and this will save me electricity.
Turn off power to the stove (unplug or turn off breaker) Remove back panel screws (Phillips) and back panel Unplug switch Remove knob and attaching screws (Phillips) Remove and replace switch Reinstall screws for switch and plugs in the back Snap off the end of the stem if it's too long and reinstall knob Reinstall back panel and turn power back on
*important: the large element has an updated switch and you may need to snap off the end of the stem with pliers! It's too long and there are no instructions for this included!*
The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.
Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.
My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.
The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.
I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.
Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
Unplugged stove. Pulled stove out. Unscrewed screws and removed cover. Removed & replaced sensor. Reinstalled cover & screws. Plugged in stove and pushed back in. Only problem was when I pulled stove out, lid opened and disconnected the gas line to a burner.
The side trim on the glass door needed to be replaced.
After we put the latch pins in, the door was easily lifted off. We placed the door on the table and unscrewed the trim pieces. The new trim pieces went into place after we cleaned the door. We slipped the door back on the oven and removed the hinge pins.
I snapped a bolt on the main power terminal block when connecting the pigtail.
Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.
Removed 3 screws holding the glass door bracket. Placed glass into door holders, had another person hold glass while I replaced the removable bracket screws.
Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.
Installed a new thermostat and noticed the convection heating element wire had burned in two. Ordered new element and installed. Oven is currently working properly again.
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
