YISR309JT5AA General Electric Washer - Instructions

Pop out pop in, just that simple.

pulled out the center agitator, undid the nut , put the new one on , easiest repair ever, less that 13 dollars. and the part came in 2 days, wow, I am impressed with your company!!!!!

The repair was so easy. I came home from work opened the boxes and got my socket set. Pulled the old agitator off with no problem. Grabbed my ratchet,extension and a socket.Took the old screw and agitator coupling off , which turned out to be the problem the inner spline of the coupling was stripped. Pushed the new coupling on used the new screw that came with the new coupling kit.Lined up the slots of the new agitator to the new coupling pushed it on,then pushed on the new fabric softener dispenser, done!!It took me longer to type this than the repair did!!

Pulled agitator by hand, (very easy), removed bolt holding coupling to shaft, removed coupling and installed new one. Tightened bolt snugly and pushed agitator bank over coupling! About 5 minutes to repair!!!!!!!!!

First I had no idea what to do. My first thought was to buy a new washing machine and so I began searching and found that a washer equal to mine was over $600. I brewed on this for a few days when a neighbor told me that they are not that hard to work on and we should take it apart and look at it first. We took the top and the front of the washer off and looked at the belt and the motor. All seemed fine. (we just used a screwdriver for that) then we took the agitator off, it pulled right off with some heavy tugging. then we saw the coupling. It was only held on by one screw. We used a socket to take the screw out and pulled the coupling off. It is supposed to fit very tightly on a shaft with gears. When we pulled it off and looked inside it, all the plastic gears in the coupling were stripped and that is why the agitator would not move. I expected this to cost me at least $50, but to my surprise the part was only $6.50. The shipping cost more than the part. When it arrived in about 3 days. I literally had the part on and the washer back together in less than 5 minutes. The entire repair cost me $14 and now the washing machine works better than it has worked in years. Who knew. If you intimidated by working on washers, don't be, they really are very simple machines and so not worth calling a repair man for.

I just popped in the new agitator. The coupler wasn't needed but I will keep it just in case.

I removed the agitator, replaced the agitator coupling. The guy at the appliance store where I was able to find the part said to check the splines on the inside of the agitator as well. Glad I did, the splines on the agitator were worn out too. So by checking both, if and when the problem occurs, REPLACE BOTH parts! This will save a lot of grief for you!

Was very easy to remove and replace. The instructional video let me know what to expect

Unit unplugged. Next day delivery, saved plastic clip and two screws from hose connect to washer , removed leaking hose ,replaced with new hose fully pushed into unit with plastic clip already in place on new hose. Tightened screws on plastic holding clip on new hose. Done complete job in 5 minutes.

took agitator off, loosened bolt on coupling, took that off. Replaced new coupling and tightened bolt on top. Put agitator on and pushed down hard to set in place. I'm a 66 year old female with no mechanical ability. I ordered this part on Sat. and it was on my door step on Mon. great service and video explained how to do repair and information provided possible repair needed. Great company.....

The motor assembly (630 in the parts diagram) has a spring pin in the drive shaft to connect the drive shaft to the clutch. The spring pin had shattered. Instead of replacing the entire motor assembly ($365), I ordered a new clip from PartSelect, and a new spring pin from McMaster-Carr. Used a screwdriver and mallet to drive out the old spring pin and install the new one. Reinstalled the clutch and clip and everything was good to go.

Removed agitator by pulling up, wiggle to and fro, watch out for unexpected release. Agitator coupler was worn, stripped splines. 7\16 socket, long extension to remove bolt in coupler. Install new coupler, new bolt, then line up agitator to splines on agitator coupler and push to snap in place.

Remove agitator remove retainer screw and using Prybar lift off the old coupler ..... After removal use heat gun and wire brush to remove plastic residue from the splines of the motor shaft ... While the shaft is still warm line up the splines from the new coupler and using the mallet force the coupler on the shaft ... Install the retainer screw that comes with the coupler and snap on the agitator ... Done

I pulled up on the fin part of the agitator exposing the gear coupling. I unbolted the nut on top with a 12 mm socket. Once the nut and washer were removed I pulled up on the gear coupling and slid it right off. Reversed procedures to install the new one.