YE20EA4 Magic Chef Dryer - Instructions

First thing was to disconnect power to the dryer. I lifted the top lid and found 1 screw on each side at the top near the front and removed them. I also removed the door switch (CLIPPED ON) leaving the wires connected to the actual switch. Then the front panel lifts up and outward. I was able to install the belt from the front, guiding it back to the pulley/idler arm. Reassembled and it worked great. The belt I bought from this site appears to be better than original stock. It should last a long time. :)

I watched an online video about how to replace a dryer belt & followed the directions. Placing the belt around the drum is easy but stringing it thru the pulley is a little difficult because the belt has tension. This takes a little effort but is doable. Dryer runs great now........Be sure to unplug appliance 1st........

Watched the video on the site and it was spot-on! Super-easy, took like 10 minutes to replace the belt. Thanks!

Lift top of dryer. Remove two 1/4" screws that hold the front panel. Disconnect the two wires on the door switch. Lift front panel to remove. Lift drum enough to install the new belt. Reach in to place the belt on the motor and tension pulley. Replace the front panel. check for free rotation of the drum and belt. Close top. Done.

First of all let me begin by telling you that this was my first D-I-Y project. The dryer had been out for over a month and the clothesline drying of clothes, while being energy efficient, did not go well because it was the summer/fall borderline and the ants and bugs were inside the clothes which were brought into the house.

I googled my problem and soon enough there were a ton of helpful sites available offering solutions to my problem. So, after I decided to do it myself, I ordered a new belt from part-select. Once the belt arrived, I went back to for help. There was an extremely useful video among the results. The whole thing took me about 20 minutes as I was doing it all by myself. I followed the steps and was able to replace the dryer belt very easily and I am so very thankful to have a working dryer again before the onset of rain and cold!

the same way it was described on your site, this dryer is nearly 17 years old, I've needed to change this at least 5 times.

Remove front panel of dyer, pry open with srew driver,be careful not damage enamel. Remove drive belt, pull drum forward and out. Drum glide are located at bottom of drum rest,rollers at rear of dyer.

Had to lift the top with a screw driver. Unplugged dryer. Removed 4 different wires from heating element. Unscrewed with socket wrench screws that are small becareful not to drop. Replaced with new heating element and there you go. I had to reset at my fuse box as well. I was overjoyed that I didn't have to go buy a new dryer so close to the Holidays!! Hopefully it will work for another 10 years. Thanks!!

First I removed the back panel (and found out later when I received the belt from Partselect.com, that this was unnecessary). I followed the instructions that came with the belt and removed the top panel and then the front panel. I placed a piece of wood under the drum for support so that it would not be just hanging from the back. Then I found the broken belt lying on the bottom, and a pulley that was unhinged. I replaced the pulley following the instructions, and vacuumed the motor and all around. I put the new belt around the drum and then through the pulley and onto the motor axle. I replaced all the panels and the dryer is now working like new.

Disassembled dryer to gain access. Cleaned out dryer and installed new belt. Reassembled dryer and checked function.

My Dearest One removed the screws that held the part that covers the bulb; removed the old bulb, put in the new bulb and replaced the cover.
The whole operation took less than 5 mins.
Thank you.

First I removed screws in lint tray, then opened up top of dryer and removed screms on side- removed front of dryer, put on new belt through idler pulley onto motor, then reassembled dryer. Really easy job and this was my first time working on an appliance

When the dryer drum stopped tumbling, I followed the instructions on PartsSelect to remove pop the top of the dryer and then remove the screws to remove the front panel. Then I could see the broken belt underneath the drum.

I did pull out the drum itself to get a better look at the motor and pulley to see where the new belt would need to go. I replaced the drum by pushing it back and then rotating it so it would fit back into the groove on the rear panel.

Once I received the new belt, I followed the steps included with the belt package to loop the new belt around the drum and then thread it over the pulley and around the motor.

The entire repair was very easy and so much cheaper than buying a new dryer.

first pryed up the dryer top, pulled the two wires for the door switch and removed front panel. remove 8 or 10 blower housing cover 1/4" screws. removed blower moter shaft snap ring pulled out damaged blower wheel. slid on the new wheel with the flats on the shaft and new wheel alighned up. installed blower clamp around blower stub. installed motor shaft snap ring. reinstalled blower cover cover. installed front dryer cover to include installing door switch wiring. put down top and pushed dryer back into place making sure to install the blower vent hose. started dryer to test operation. all worked well the first time.

I followed instructions here on this site, and repaired the dryer with ease. More details in other posts but it pretty much went like this:
1) take out screws under lint thing, lift top
2) take out two INSIDE bolts in the top of the dryer (5/16" socket), disconnect wires, lift then set aside front
3) clean everything out, set dryer on it's back.
4) wrap belt around the tub (rubber facing the tub), and then loop it through the tensioner (which will have fallen out of place, but you can see from the wear where it goes). Note it loops through the tensioner then over the motor wheel, and then back through the tensioner. Took me a little while to figure that out. (put tensioner in place before doing the looping through)
5) put it all back together.
Very satisfying to have it all work again!