WWSR3090T2WW General Electric Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Knob broke off. piece of knob plus clip were still on washer.
after seeing new knob and clip, realized to pull old clip off and small piece still on stem. put clip half on new knob, put it on stem. very little room behind it. pushed clip down rest of way with very thin screwdriver. snapped in place. all done.
Parts Used:
-
Howie from Danville, IL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The Roll pin had shattered destroying the clutch clip
The motor assembly (630 in the parts diagram) has a spring pin in the drive shaft to connect the drive shaft to the clutch. The spring pin had shattered. Instead of replacing the entire motor assembly ($365), I ordered a new clip from PartSelect, and a new spring pin from McMaster-Carr. Used a screwdriver and mallet to drive out the old spring pin and install the new one. Reinstalled the clutch and clip and everything was good to go.
Parts Used:
-
Alan from SIMI VALLEY, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench set
Was this instruction helpful to you?
Thank you for voting!
machine wouldn't agitate
took agitator off, loosened bolt on coupling, took that off. Replaced new coupling and tightened bolt on top. Put agitator on and pushed down hard to set in place. I'm a 66 year old female with no mechanical ability. I ordered this part on Sat. and it was on my door step on Mon. great service and video explained how to do repair and information provided possible repair needed. Great company.....
Parts Used:
-
Bonnie from Erie, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
Agitator not working, spin cycle ok.
Removed agitator by pulling up, wiggle to and fro, watch out for unexpected release. Agitator coupler was worn, stripped splines. 7\16 socket, long extension to remove bolt in coupler. Install new coupler, new bolt, then line up agitator to splines on agitator coupler and push to snap in place.
Parts Used:
-
Walter from Atlanta, GA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Stripped plastic coupler spline
Remove agitator remove retainer screw and using Prybar lift off the old coupler ..... After removal use heat gun and wire brush to remove plastic residue from the splines of the motor shaft ... While the shaft is still warm line up the splines from the new coupler and using the mallet force the coupler on the shaft ... Install the retainer screw that comes with the coupler and snap on the agitator ... Done
Parts Used:
-
frank from palm city, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
old knob broke
Opened the package - put it on just like the old one. Didn't take 5 minutes. Good as new.
Parts Used:
-
Jacquelyn from Bokoshe, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The gear agitator had striped. Wouldn't spin the blades to wash the clothes.
I pulled up on the fin part of the agitator exposing the gear coupling. I unbolted the nut on top with a 12 mm socket. Once the nut and washer were removed I pulled up on the gear coupling and slid it right off. Reversed procedures to install the new one.
Parts Used:
-
Gerardo from Mountain House, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Wrench set
Was this instruction helpful to you?
Thank you for voting!