WWRE6260D1WW General Electric Washer - Instructions

took agitator off, loosened bolt on coupling, took that off. Replaced new coupling and tightened bolt on top. Put agitator on and pushed down hard to set in place. I'm a 66 year old female with no mechanical ability. I ordered this part on Sat. and it was on my door step on Mon. great service and video explained how to do repair and information provided possible repair needed. Great company.....

After the GE Washer went dead last week Tuesday while my spouse was doing laundry, I I took it to the back yard just to examine the inside from beneath before going to find a new one that evening.
While on its back I notice that the motor still worked but it was very weak. Taking the belt off it went a little faster but weak. Then I remembered that there was supposed to be an electrical part that sends or allows current to go to the motor, but didn't know the name nor what it should look like.
I started my search and found this cylindrical electric part that had a scar on the outside and a hardened mass protruding from the inside. Since the wires to and from the part was the same color, I marked one terminal, then took pictures of the position and wiring of the part I identified as the problem, then took it out of the machine.
At this point, I went to the car, sat inside, started the car, and was about to leave to find a washing machine, then I thought of the Internet. I went on the Internet, found a store that sells GE washing machines parts, identified the part to be the capacitor. I ordered the part late that evening, received it Thursday afternoon, installed and reassembled the machine immediately, and today is the eight day since the fix and as I am writing, Thursday, August 15, 2013, the machine is doing my laundry. The diagrams made it very easy to identify the name of the part, and since I am mechanically inclined, getting the old part out and installing the new part was very easy. ~~ Vasco

I noticed the agitator would spin all the way around, in each direction. Also, the machine would make no sound, associated with washing, during that part of the cycle. I pulled the fabric softener reservoir off, with fingers on each side of the agitator, i pulled straight up and that gives you access to the coupling. Use a 7/16'" socket to loosen the nut, remove it and pull the coupling off. Press the new coupling on the splined shaft, tighten nut, and line up agitator with the grooves, push it down and replace fabric reservoir. Straightforward repair.

I had no intention of trying to fix the washer myself after reading about how to do it, only because I didn't know what half of the words were referring to. But once I watched the video, and I saw that the part was going to cost less than $15.00 (shipping included), I thought I would at least try it before going out and buying a new machine. The washer in the video was slightly different than mine, but I recognized the parts from my machine and mine was actually easier to replace than the one in the video. I just pulled off the agitator, unbolted the old agitator coupling and replace it with the new one, bolted it back on and lined up the agitator grooves with coupling and that was it. It worked and saved me a lot of money. I once had an appliance repairman tell me that if your washer or dryer lasts 7 years nowadays, you should consider yourself lucky. Mine is 7 years old, so I thought I would have to replace it. I didn't particularly want to pay someone $100.00 to come to my house and tell me it couldn't be fixed if I was going to have to buy a new one. But fixing it myself was very easy. Written instructions never would have worked for me, but the video was very helpful. Thanks!

Fortunately I watched the video on how to change the knob. I may not have noticed that the metal clip part of the old knob was still attached. Once the old part was removed, the new knob slid right into place.

My washing machine began smoking one day while on spin cycle. I freaked out and turned every breaker off on the electric panel since I, apparently, forgot how to read during this episode. Once the smoke cleared and my brain power returned I removed the front panel of the machine. After a quick look I decided I saw nothing wrong that I could fix. 24 hours later my brain had returned to normal functioning capacity so I decided to turn the power back on to the washer and see what happened. It was then that I noticed the smoke coming from a black cylinder on the front of the washer. I googled my washer and the VERY helpful diagrams from partselect.com came up showing me this was the capacitor. Since as mentioned previously my brain was now functional again I was able to determine this would be an easy fix, ordered the part, got it 24 hours later (!!!!!) with no special shipping, and installed it in 5 minutes. I feel smart today! Thanks Partselect.com!

replaced circuit board and housing, I have never done this before, but at this time, with the way the Presdent and Congress is taking everthing away, you need to save every penny. So I talked replaced it myself..and saved about $200.00.

Unplugged the unit. Removed water hoses. Removed 4 "star" screws to open control unit cover. Unscrewed assembly with philips screw driver. Unpluged electric plugs. Used pliers to remove internal hose. Removed bad unit which was plugged with hard water corrison. Reverse steps to reinstall. It worked great. Loved the online ordering and shipping direct to my home.

Unplug power. Pull up firmly and quickly from the base of the agitator. Some videos used a rope and 2x4, I didn't have to. The agitator just pops right off. Then with a 7/16" wrench unscrew the bolt while holding on to the coupling. Take agitator coupling off. Clean off metal grooves that the coupling goes on, use either a small screwdriver, metal brush, a knowl, just to make sure you will have good connection with the new coupling. Then install the coupling, new nut, tighten nut firmly. Install agitator pushing down firmly on opposite sides until snaps in place. Turn agitator by hand, it should not free spin. Plug power back in, run washer with water and bleach only in the smallest setting and let it run through its cycle. This will take care of any black debris that might have got into the bowl while fixing. GOOD LUCK!! I also used videos found on Google.

The washing machine was a making a very loud noise when it got to the end of agitation and though it did complete the cycyle it was beginning to snag clothes under the agitator....don't know how. Found that the agitator coupler was cracked in 4 places. Washer is only a year and a half. 4 family washing..so I wanted this fixed quick. The part came super quick..like two days and I was not expecting it for 4 - 10 days...so great and it was cheaper than other places I checked even with paying shipping! I watched the video of installing the coupler--very helpful! I removed the agitator, then removed the agitator coupler....this was already done before the part arrived. When the new coupler arrived, I just had to drop it down onto the spline...there are grooves it must fit to...then I applied the hold down bolt. I used my wrachet/socket to tighten it, but you can use an adjustable wrench. I'm short so reaching down into the washer bowl to get to tighten the bolt was a little ackward..should have used a stool. The loud sound the washer was making before replacing the part stopped and I am back in business...doing ugly washing....LOL! One thing I will mention....nothing to do with the part...but I had without thinking placed the agitator back into the washer bowl....WITHOUT bolting it down..then put the agitator on top of the old coupler. So this made it lock in place under the agitator. My agitator does not have an opening at the top after removing the dust cap inside so there was no way to knock the coupler down and out from the top by putting a long wrench or something down through the top of the agitator(the video shows how to do this also)...sooo....because the agitator coupler locks in place behind moveable clips, I took eight butter knives and wedged them behind each clip on the underside of the coupler pushing each back and was then was able to separate the agitator coupler from the agitator by pulling it forward with my fingers...so don't test putting the agitator over the coupler without first bolting it down! This is all a lot to say about such a small part but this small part is crucial to being able to complete a wash..an ugly wash that is...haha!

removed agitator unscrewed agitator coupling replaced with new one replaced agitator

First unplug the washer. When changing the tub straps first remove the magnet switch from the lid. There is a tab at the rear of the switch & then you can bring the switch into the washer & then remove the lid assy. This will save the switch. If you do like I did then you will have to install a new switch because the lid fell & broke the switch. Installing the new switch was fairly easy. Push the tab at the rear of the switch in & push the switch up. I cut the two wires about 3 inches from the old switch & then strip the wires. I installed the two butt connectors before putting the switch in the washer. Then crimp the wires to the corresponding colored wires. Put the front back on the washer.

As directed by the book.

All I did was stick the knob on. How easy was that! Knob works every time. Very pleased with the part.

Took off old agitator, removed coupling that was bad and put new one on.