WTW5550XW0 Whirlpool Washer - Instructions

I used a jack to lift the tub and unhooked the rods and replaced them. Works great.

removed old lid from hinges and replaced with new one using a Phillips screwdriver. You do need a special screwdriver to replace the lid lock as it has a different kind od screws which I didn't have. Luckily my neighbor did.

The info. was really helpful

Just follow the video! Very easy.

I ordered a lid switch because the washer wouldn't agitate. Most reviews indicated that was the problem. While waiting for the part to arrive, I discovered the transmission to be of fault.I let parts select know that I no longer needed the part. Parts Select gave me an immediate refund no questions asked and before I returned the part to them. That is customer service!! I will use Parts Select for all my future purchases. I can trust a company that trusts its customers.
Joe M. San Jose

Followed video provided by Part Select. Video made it look easier than it was but was very thorough and I was able to accomplish repair in less than an hour! The agitator before repair would bounce up and down when I pressed hard and let go. After repair it was much tighter!! Evidently this is a common problem with this design of Whirlpool washers!

First problem I found, feed hose has cone screen . this was half clogged with black debris ,from deteriorating feed water hose ,(replace hose).old valve did not have internal filter inside port, but new one did. When removing old valve. lift up out of feed ports. Look for black rubber debris, from tube seals floating in box. You can remove particles with Q-tip and a pair of tweezers. After that, I have full flow. Great looking part, Fast delivery. 5 stars.

Watched video and followed instructions. Removed rods from top cups, laid washer on its side and pulled them out. Put new rods thru, stood washer up and hooked them in. Was pretty easy, tube heavy but I'm 52 and I did it myself.
My only problem is there's no springs anywhere attaching rods to tub and I cannot find any info on 1. IF I need them 2. What kind I need. I sent email to partselect last week inquiring and still waiting to hear.

Removed 5 screws on back, released 2 retention clips on front, lifted top of washer to expose lock assembly, removed 2 screws holding lock assembly in place followed electrical line back to plug behind control panel plugged new lock in, and reassembled in reverse order. Done!

Found common diagnosis and instructions on internet. It is not difficult to replace.
Unfortunately, this new latch assembly did not fix the problem.

I put the dial to drain and and pressed the pause button for 3 seconds and it drained.
Unplugged the washer from the electrical outlet .
Shut the hot and cold water off. Disconnected and drained them.
Placed the washer on a soft mat on front side exposing the back and bottom of the machine.
Unscrew the metal cover with Philips head screw driver.
Disconnect the drain hose to a bucket or small dish tub .
Remove the belt cover with 5/8 ratchet or wrench.
Using a ratchet or wrench remove the one bolt holding the clutch in place .
Remove the two Philips head screws from the shift mechanism ( looks like clock timer,my memory is failing me right now sorry! ) .
Pull down on bottom gear after removing nut.
Push in and pull down with a flat head screwdriver on the tabs holding the collar in place above the top gear .The collar and gear and spring should come apart.
Install new parts in the same order . Reassemble make sure to use Locktite 242 on the bottom nut holding the gear.
Install belt , belt guard , cover drain hose . Stand machine back up , reconnect all hoses tightly plug machine into electrical outlet and start. Put a smile on your face because you did a great job and saved yourself some money!

Once we put the washer on it's side noticed lots of oil on the floor and in the belt cover area. Replaced belt anyway but issue is the leaking transmission. Starting warranty process since Maytag carries a 10-year part warranty and machine is 6.5 years old. Wish me luck !!!

Followed detailed instructions which were supplied with the parts. It was easy and my machine is working great with no issues. Also I just didn’t get the main drive pulley, all new parts came for the bottom end, great service and excellent parts.

Took the Cover off and installed belt.

The part we needed wasn’t pictured — nor the quantity identified. There are 4 absorbers required for full replacement. I received one absorber — 3 1/2 inches X 1 1/2 inch wide X 1/8 inch thick. Including shipping, the cost was $53.00!! Outrageous! A 10 foot roll of the same thing can be bought online for less than $20.00.

By the way, it didn’t solve the problem.

Paul