All Installation Instructions for Whirlpool Washer WTW4800XQ0

Making Alot Of Nosie While Washing

First I removed the fabric softner dispenser. Then I removed cap took screw out removed agitator asseembly put new one in then I put screws back in.

Parts Used:

Washer Agitator

CHRISTI from NEWPORT NEWS, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set

12 of 18 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

would not move clothes

Took the cup for the clothes softner out, just pulls out, took plastic seal out, just pulls out, took the socket set,with an exstention, unscrewed the bolt & pulled out the agitator. easy. Reverse the process in putting the agitator back. P.S. Right hand thread.

.

Parts Used:

Bottom Agitator

phillip from worcester, MA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

15 of 27 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Wouldn’t drain pump made loud noise

Removed old drain pump and found a sock in the inlet - must have burned out pump because after removing it pump was still defective. Installed new pump in about 30 minutes and off to the races no more issues

Parts Used:

Drain Pump - 120V 60Hz

REED from BUCHANAN, NY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Wrench (Adjustable)

10 of 13 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

wash machine walked

watch utube instruction.easy repair

Parts Used:

Washing Machine Suspension Rod Kit

Elzoria from FROSTPROOF, FL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers

9 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

replaced drain hose that was missing

slipped the new drain hose on and with locking plyers slipped the wire clap in place after three trys

Parts Used:

Washer Drain Hose

Delmar from EAST TROY, WI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers

11 of 16 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Both outside door handles turned very beige

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Parts Used:

Spray Paint - 12 oz. - White

Howard from Boynton Beach, FL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

22 of 50 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Top half of aggitator was not moving.

Replaced agitator cog/clutch unit under the softener dispenser. It is the second time I've replaced it in the last 3 years, maybe it has been loaded too heavy, I'll have to have that talk with everyone else on the family who does laundry.

Parts Used:

Agitator Cam Kit

Stephen from Stansbury Park, UT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

9 of 11 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Upper Agitator Ratchet Broken

1. Remove Top Cap.
2. Remove Seal Cap.
3. Remove 7/16 Bolt
4. Lift out Old Agitator
5. Put in NEW Agitator
6. Replace 7/16 Bolt
7. Replace Seal Cap
8. Replace Top Cap.
9. Sit back and enjoy your clean clothes

Parts Used:

Washer Agitator

Mathieu from Palmetto Bay, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

8 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

lid would not lock, washer would not run...

Removed old striker ( 2 Phillips head screws ) replaced with new striker with the 2 screws and was done, easy fix...

Parts Used:

Lid Latch Strike

John from Hale Center, Texas, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

8 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

washer wasn't spinning after rinsing but the motor was running

I had taken the time to watch videos of this repair so when the switch arrived I knew what I had to do. Removing the screws to get the back cover off was simple as was installing the switch. No tricks here just watch the videos and your all set to do the job

Parts Used:

Drive Belt

Terry from HANCOCK, MD
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers

8 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

I followed the video guide, which was excellent

I followed the instructions, however I did not have a spot to hold the bar temporarily, so I drilled a hole in the corner frame to hook them in at the front of the machine. All else was easy and according to the video.

Machine works great now.

Parts Used:

Washing Machine Suspension Rod Kit

Richard from NAPLES, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

7 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Making loud noises.

The video you sent me was very helpful told me the exact tools I needed and how to do it.
Thank you

Parts Used:

Washer Drive Pulley

Roy from BROOKLYN, NY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set

8 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

need to have a fabric softner dispenser

the first order was ordered wrong for me and the part was to big so I had to send it back and order another. The second dispenser was the right one and went on well to the machine. Just had to put it on the machine by hand.

Parts Used: