Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer stopped working
What a mess. Partselect shipped the wrong part. I paid a technician to fix it, only to learn the part was wrong. I order the right part. I needed to send it back, reorder the same part, and pay for a second visit from the technician. The nice people at partselect gave me a $7 credit for costing me $200. Losers
Hardest part was getting the top off which ended up being quite easy, once I knew how. At the front of dryer, between the top and the cabinet, there are two spring clips that hold the top to the bottom. I could feel them with the putty knife but wasn't sure how to release them. Push on them with the blade of the stiff putty knife ... push hard and they will release. When the top was off I could see the screws that held the front. I unscrewed those, had easy access to the front glide that needed to be replaced. Pulled the old one off, followed the directions to glue the new one on, gave it about an hour to dry, reassembled and away we went. No more snagging.
I like to fix , i have time and i just give me the chance to try , and i did it , i wish to pay less for the parts , but was a good feeling when the problem fixed
Squeaking was coming from the back of the drum, not the glides. The hardest part was trying to figure out how to pull the drum out. With a little extra tug, the back pin of the drum lifted out of the socket. That was the cause of the sqeak. Just cleaned it up and added some grease and good as new. I noticed the front glides were worn and replaced it.
I ordered the rear bearing kit from the local supplier here in Marsh Harbour, Abaco the Bahamas. Delivery for the kit was 3 to 4 weeks from my local supplier.NOT PARTSELECT. While waiting I found this site and after reading the VERY helpful instructions from your customers, I realised that I would probably need additional parts, top and bottom front felt seals, maybe a new drive belt. I ordered these online and had the parts deliverd to a friends address in West Palm Beach Florida. The parts arrived in about 2 days. My wife was already there and brought the parts back.
Installation was very straight forward. Read the other installation reports and you will not have a problem. The only thing I can add is, DO NOT LOOSE THE SMALL BALL BEARING. I did and it took me about an hour to find it. My suggestion is to do a dry run installation of the bracket WITH OUT the small ball bearing. Tape the backing plate?that keeps the ball breaing inplace to the outside of the back panel with duct tape so that the screw hole will line up. Once this is done put some grease (Supplied with the kit) in the hole on the nylon bracket and attach with the two screws, do not over tighten. Grease up the area where the rear bearing shaft support will sit.
Installation of the rear bearing shaft support was straight forward. This is on the dryer drum. Extra hands are must for this.
I was very pleased with Partselct. Dryer works like new.
left a drywall screw in my pockit and it cut the tub
I first made a repaire order online and put on the service order that i needed a new tub. Someone was to call me the the night before but i never got the call the service man was coming between 8am and 12 he called at 11 and wanted to come and look at the washer to see what parts he needed i told him i put in the service reqwest that it needed a tub and that if he didn't have the tub not to come because i was not going to pay for a service call if he didn't have the parts he did tell me it would cost me $430.00 so i repaired it myshelf
I first checked the heating element by peeking through the peek hole in the front to see if it was turning on. The heating element turned on but gas failed to flow. Next, I checked all sensors including the fuse, they were all fine. This points to the solenoid as the cause of the issue. So I replaced the solenoids and the problem solved. I did watch the YouTube video on how to check the sensors and replace faulty parts.
Removed top of dryer, took screws out of back of dryer, pulled drum off front of dryer, removed old belt and slid new one in place. Reattached drum to front and slid belt in place only to find it was the wrong size. Called an appliance repair man, he said happens more ften than not.