WRT779REYM00 Whirlpool Refrigerator - Instructions

I removed the screws on top of the refrigerator and the freezer door, lifted the fresh food door off bottom hinge laid it on a covered floor, used a pair of wire cutters to cut old gasket. then pulled the gasket straight out all the way around. then I started on one corner using a putty knife to push the new gasket under plastic trim, then put gasket on opposite corner at top of door then did the same with other two corners, then used putty knife to go all the way around sliding gasket under trim. was easy.

unplug, turn water off, remove ice maker & unplug,remove back panel remove old fan unit & unplug remove fan remove fan blades just pull off install new fan, put fan blades on new fan & install on bracket & re install plug in re install back panel. plug in ice maker re install ice maker . turn water back on plug refrigerator back in ( quite easy )

I removed the 3 screws but also removed the front screw of the left bin rail. This gave more room to maneuver I/M into position. The cover shown with the enclosed instructions does not show an Ice Plus (blower assy.). By removing the two mounting clips fron old unit and snapping on new one blower unit fits as original. Overall a very simple and quick repair. Note: None of the cables Inclosed were used as my harness does not unplug from wall. Thanks for the quick service PartsSelect.

Turned off circuit breaker. That turns off both power and water. No need to move refrigerator. I backed out the 2 top screws about a quarter inch and then removed bottom screw with a quarter inch nut driver. I then lifted Ice Maker clear of the two top screws and lowered it enough to unclip the power connection. The new Ice Maker was wired correctly for my refrigerator so all I had to do was reconnect the power connection and mount new Ice Maker on the two top screws and install the bottom screw. It took about two hours for the new Ice Maker to start it's cycle but after it did, it worked GREAT. Part Select service was OUTSTANDING, ordered part one day and received it in two days and I live in a very remote location. Recommend PartSelect to everyone.

the repair it good and easy ,vo helper to do it.

Instructions came with the part I ordered and they were very easy to follow. Basically you have to remove the cardboard cover from the back. Then you remove the four screws at the bottom (2 front, 2 back) that hold the bottom plate on. My husband tilted frig and held it while I put a block(4" x 1/2") under the bottom outside frame (not the bottom plate). You can see a ridge on the frame which is where I placed the block. My husband braced the frig the whole time I did the repair just to ensure it didn't fall on me even though it was blocked. The bottom plate didn't slide back at first. I took a flat screw driver and hammer and slightly tapped the bottom plate through the screw hole that secures the bottom plate to the frame. I tapped 2 or 3 times...gently each tap...until the bottom plate dropped down. Which was the 1/2" noted in the instructions. I then was able to access the front wheel, remove the pin and replace with the new one. We replaced both front wheels so I did not replace the bottom plate until we replaced the second wheel. We removed the block and tilted the frig to the opposite side, blocked then I replaced the second wheel. Once that was done I removed the block, my husband let the frig down gently and I went to the back and tapped the bottom plate forward. It didn't quite want to go back in place but with patience it finally and then was able to put all screws back in. Donna

I followed the video on the web site. Easy squeezy.

Should have. . . . Just taken the ice maker out in the first place . . . . When I saw no ice I assumed the timer was bad. . . Replaced it. . Then when that didn't fix it again assumed that water valve was bad. . . . Replace that also to no avail. . . . Finally took out the ice maker and saw that the heater had stopped working cuz there was still ice stuck in it. . Replaced ice maker. . . All good. . . The water valve I replaced was a good thing cuz you can definatley tell the difference. . . . Anyway. . . Fixed!

Online I learned how to diagnose the problem and order the part I needed. Replacement was simple and now we have ice. It works perfect, no adjustments needed.

Spent six hours melting the ice berg, twenty minutes cleaning things up and ten minutes replacing the ice maker. The video was great the only piece of information that was missing was a statement that it may that several hours for ice to be produced. Thanks for the prompt and courteous support during ordering, a good product and support video.