WRS6R3EWA Crosley Refrigerator - Instructions

I just pulled the old gasket out , pressed the new one in with my thumb,and was finished. thank you, Langley

The shelf bin is a piece that anybody can clip it on the door in less than 30 seconds. No tools required, just simple common sense.

I located the part that was the culprit as it had buzzed very much before quitting. This is an easy removal as the part is in a two prong jack and just needs to be carefully removed with the new part inserted back in the jack provided. The refrigerator works fine now, but the run capacitor will still buzz on start up of the compressor. I do hope this is normal in this model? anyway it runs fine mow. Thank you.

First I removed the door. Took off the broken parts and replaced them. Easy and fast to repair.

I ordered the complete part and installed in about 10 minutes. The order went very fast, part was in stock and everything went very smooth. PartSelect.com was very easy to work with and they have a very satisfied customer. I will definitely use PartSelect.com again. Thanks for the great service

One of the bins on my freezer door had the tabs, that hold it on the door, broken off. I orginally ordered the wrong item, but I called right away and Parts Select had the correct item to me immediately. It was a very easy fix, I just had to snap the bin in place once it arrived.I am very impressed with PartSelect and their service. I would definately use them again and recommend them to others.

Removed stuff on door, removed 2 screws on top of door, lifted door off replaced one door closure/hinge bearing and one door closing plate and put door back on and wala no more thump.

Unplug refrigerator. Take out spill tray by sliding out. remove bottom 3 screws, gently but firmly push up and against refrigerator(Top section of cover snaps in by pulling cover down while holding cover against refrigerator). There is a ribbon wire connecting the two boards, care not to tear it out of connectors. There are two tabs on the plastic connector holding the ribbon wire to the outside board,pull the tabs out a little and gently pull the ribbon loose, carefully. There are 3 screws holding in the back board, remove them, them remove water hose from water actuator so the assembly can come out. Gently spread the plastic holder to be able to take the broken paddle out. Watch closely how the third arm on the actuator(Lower left arm)is resting on the back of the flapper.Replace the Actuator exactly the same. Just reverse the steps to install the rest of the parts.(Had a time getting the water hose back into it place. I used pliers to push and wiggle it back into it opening).Don't forget to plug the frig back in again. DOOR CLOSING CAM AND HINGE BEARING ARE VERY EASY. It take about 10 to 15 minutes to do. Empty door drawers before procedure the screw holding the plastic cover, remove cover. I used a 3/8" nut driver and my cordless drill to take out the two lag bolts holding the top hinge.Lift door off bottom hinge. Replace Door Closure/Hinge Bearing. Reverse procedure to finish installation.

Went the typical route of part replacement since I don't own an ohm meter...pull and replace one part at a time. Started with the cheaper parts first, replaced the freezer fan for $40, same problem. Replaced the defrost heater element for $40, same problem. Replaced the thermostat $15 and controller board $150 at same time, bingo problem solved. Had to defrost with the hair dryer each time, biggest pain. Had an issue finding a Utube that showed the water filter system and thermistor removal for this model, otherwise straightforward, but not a 30 minute job.

I ordered 3 items based on my model and serial number from the website.

The new bin arrived, I slid it in place and away we went.

First I removed the plastic drip pan that catches the ice and water. There were two or three screws that had to be removed. Next I removed the old broken actuator and put the new one in. There were two more screws to be removed to replace the old actuator. Those screws were pretty small and hard to get out. Other than that, the new actuator went right in and was working in no time. Overall a pretty easy project.

No problem, I Just pushed the plastic pin to the old support studs into the frig wall using a small screw driver and hammer and with pliers pulled the studs out to the wall of the frig being careful not to damage the wall. Then with pliers {needle nose} pulled the plastic pin out of the wall. Pushed the new support studs in the hole and tapped the plastic pin with a small hammer into the support stud. Replaced crisper drawer cover and glass shelf. Easy fix

removed ice maker box and disassembled crusher unit on front of box and installed new housing.

Followed instructions from others on the blog. Shut off water and electricity to the refrigerator. Removed the cardboard plate. Removed the old water valve. Cut the compression valves off and inserted the tubes into the new water valve. Attached the water valve bracket to the fridge. Tightened copper water supply.Turned on the water - no leaks. Plugged the fridge in. Tried the water and ice in the door. No leaks - everything worked perfectly. THANK YOU PARTS SELECT!