WRS3R3EWE Crosley Refrigerator - Instructions

Turned off water to refrigerator and unscrewed canister, removed filter reinstalled canister and ran water thru to get all sludge from line. Turn water back off. Remove canister and install filter reinstalled canister, turned water back on. Run water thru line. Job complete. No problems.

I tapped in the peg like it showed in video and pried out with flat screw driver and hammered other peg in flush with part

unplugged frig, removed shelves & inner lower back panel in freezer side, removed defrost thermostat from tube, cut the wires and spliced in new stat wires with provided wire splices crimped together and replaced thermostat on tube it has been a week and no ice so far??. this was after 2 trips by the repairman who replace the defrost timer board which was most likely good at a total of $160!!! still cheaper than $1000 for a new frig!!!!!!!!!!!!!!

watched the attached video and repeated the steps super easy once you know how. less than 10 mins start to finish

Took out the ice box, dumped the ice. Let warm up a bit. Then took out the housing and installed the new one. Works great. Saved a lot of money! Only took a couple days to receive the part. Great service.

thanks to all of the people who had the same problems I was able to make a quick fix on my fridge. I pulled the back cover off and found the compressor not kicking on so I replaced the start cap. and im back in bussiness.

Installed them within 5 minutes

When my wife and kids moved down they lost the upper bracket and the screw for the lower cam. parts show up and matched perfectly to the orginal no issues at all

I turned off the water, removed the cardboard cover from the back of the refrigerator; removed the 2 screws holding the water valve in place; unscrewed the plastic tubing from the valve; unplugged the wires to each solenoid (3); the old valve had threaded connections for the plastic water lines, the new valve didn't; I had to cut the ferrel off of the plastic lines so I could insert them into the new valve and then press the connector into the valve (I didn't anticipate something like this, but it worked fine); I reconnected the wiring and screwed the valve back into place. The ice maker started making ice and the water stopped dripping from the dispenser. The best $65 I've ever spent.

The website said 60% of people with same refrigerator problem solved the problem with a new fan kit. I received the fan kit within 3 days of ordering. Was shipped from Fresno, CA to Long Beach, WA. The fan kit was to be installed behind rear panel in the freezer compartment. When I removed the old fan motor, I noticed the shaft turned harder than the new fan motor, suggesting a problem with the old fan motor. I plugged in the obvious fan motor power bundle with no problem. The instructions and diagram with the kit nearly steered me wrong. Instructions, diagram and splices with the kit instructed to cut the "extra" wire bundle and splice "similar" wires (should have said same color wires). Luckily, I ignored those instructions when I remembered the U-Tube video depicted the extra wire bundle was to be inserted into a factory penetration in the back panel, facing the freezer compartment. This power bundle is for adding an ice maker, which my refrigerator did not have. When reassembled and the refrigerator restarted, I could immediately feel forced air in the refrig, where there was no flow before fixing. I observed that all the refrig and freezer dials do is act like a valve to increase or decrease air flow to the compartments. The dials have no mechanical or electrical connections, just designed to divert air flow from across the cold 'evaporator' fins. I recommend other consumers to remember carefully what they see in the video and watch again if stumped during the job. The video was better than the instructions which may have been written in China or India. I am happy. Repair was a lot cheaper than a new refrigerator and I would not have bought another Frigidaire. Thanks to this website. r. andersen

We watched u tube repairman then did exactly the same thing. Then we did a high five.

Replacing the shelf was a "no-brainer." I just wanted to say thank you for PartSelect for the more than excellent service.

followed the video and had little or no trouble loosening or tightening bolts or phillips head screws. The only difficulty was removing the spacer on the door itself. Otherwise a piece of cake. Good video and easy to follow instructions.