WRS26MR4JW1 Crosley Refrigerator - Instructions

before I started a check and tested the defrost thermostat and the evaporator fan this one was working .a did check the heating coil system with a digital multimeter tested ok, at the end find out that the thermostat was not working. I put a new one. I just notice after few days some frost is on the wall of the freezer side .can some one help I don't know what else to do .can be the defrost timer .but how you test the one on this model. this one electronic thank you

used videos and followed instructions to repair. The water inlet valve was first changed because no ice was being made. Changed ice maker due to no cycle and no sound came from it. The water filter was then changed due to length of time since last changed. Plugged up refrigerator and turned water back on and within 2 hours we had ice again.

Just slide out the old part, slide in the new one, took less than 10 min

First I watched the PartSelect installation video. Then unplugged the power and shut off the water valve on the wall. I used a 1/4" nut driver and removed (4) screws on the back bottom cover of the refrigerator and removed the cover. I removed the (2) mounting screws on the back lower right side of the refrigerator and removed the triple water valve assembly. I then marked the (4) water lines and (3) solenoid connectors with numbers, to make sure they get connected back in the same place, and then I removed them. I used a retractable blade knife to cut the ends of the water lines perpendicular. I pushed the (4) water lines into the valve holes and plugged the solenoid connectors back onto the new triple valve assembly. I mounted the new triple valve, put the back cover on, turned on the water, checked for water leaks. There were no leaks.Then I plugged in the power and waited for it to fill up the ice tray. It works perfectly now ! And it was really easy ! Thank You PartSelect for making this repair easy for me.

After trying several times to fit the wiring harness beside the ice maker without any success, I folded the wiring harness behind the ice maker. Between it and the back of the freezer.

The replacement pieces for my refrigerator were easy to install and took about 3 mins to attach 3 shelves and 1 bin.

Ice crusher cylinder broke (its plastic). I use a lot of crushed ice. I just ordered the entire drawer. It was just easier to just remove the old one and push this in. If one part goes then another will follow soon Works great.

just hung it on the door. thanks for your speedy delivery. i was great to do business with your company. i will be ordering down the road. thanks again.

1. Punched the little circle bolt at the top of the drawer support all the way through the refrigerator wall using a hammer and awl. Removed the remainder of the old drawer support. 2. Previous two small alignment prongs were stuck into the alignment holes, so I had to snap off the alignment prongs on the new drawer supports with pliers to make the supports fit flush with the fridge wall. 3. Stuck new drawer supports into holes in the fridge wall and hammered in circle bolts with hammer.

Simply placed new bin in place. Took less than 60 seconds.

Turn off the ice maker.You don't need to turn off the water. Find the water filter in the upper right corner of the refrigerator. It's the round thing with a shallow round depression in the center. Push in on the center and release. The old filter partially pops out. Remove it.and throw it away. Insert new filter and push until it locks in place. Run water through the new filter until it runs clear.

Taking it apart is sort of common sense, however putting it back together can be made a lot easier using todays technology of . Digital photography. Take pictures at each stage of disassembly and reassembly be comes very easy and you may only have to do it once instead of multiple times.

after I contacted Frigidaire and they told me that it was the vent fan and told me where it was, looked up the part and got a new one from Part Select. When it arrived I unplugged the old one and plugged in the new one and reattached the holding bracket. No tools required. I then turned on the dishwasher and it works perfectly. If you get an "ou" error message on your Frigidaire Dishwasher, the money you will save is great!!!!

I should have ordered start kit instead of start capacitor. The start cap astir did not fix problem so I ordered kit. Compasator comes as part of kit. Followed enclosed instructions. Cut existing wires and reconnected new wiring. Simple as that. It's a plug in item. Now worried it may be working to good. Freezer down to 10 deg. Watching to see if compressor is running to long. Seems ok lol. Wife hates me now. She wanted new frige.

Removed the old ice container. Washed and dried the new one and installed. Works wonderful.