WRS26MF5ASF Westinghouse Refrigerator - Instructions

door handle off but 2 screws top and bottom of handle that attach to door remained under top and bottom molding. had to remove molding which was tricky. Held onto door with plastic clips which several broke when trying to get molding off. Figured out I had to tap top molding up to remove. unscrewed pieces of door handle and attached new handle. Had to use contact cement to secure molding to door where clips had broken.

First I removed two screws per rail and removed the old rails. I replaced with the new rails and used a nutdriver to secure in place. This was extremely easy and I fell like my fridge is brand new again.
You can do it!!!

The retaining wire keeping the starter in place was first removed then the starter was easily removed. Pulling the old wire off was a little difficult because I had to pull harder than I expected. Getting the wire back on was probably the hardest part. I had to compress one part of the plug so I could get it to fit back on then it was simply a matter of placing the starter back in position and replacing the wire that holds it snugly in place. 20 minutes or so start to finish and new starter works well.

I ordered 3 items based on my model and serial number from the website.

The new bin arrived, I slid it in place and away we went.

Unplugged fridge from outlet. Removed rear panel on freezer side. Removed defrost thermostat from tube and cut wires. Installed new thermostat by matching color coded wires and crimping with supplied connectors and snap back on tube. Reinstalled panel and shelving.

I recieved the part within 48 hours. I snapped the part in place and I was done in seconds.

Replaced an evaporator motor which had previouly been put in to replace original with an alternative which changed the original electrical connectors. Had to replace those replacements witn originals which extended the changeover.
Now works like the original and very quiet because your motor fit in the original rubber bushings. The alternative motor was put in by the Frigidaire repair man and at considerable expense because the warrenty date had been exceeded by one month.

removed ice maker box and disassembled crusher unit on front of box and installed new housing.

No problem, I Just pushed the plastic pin to the old support studs into the frig wall using a small screw driver and hammer and with pliers pulled the studs out to the wall of the frig being careful not to damage the wall. Then with pliers {needle nose} pulled the plastic pin out of the wall. Pushed the new support studs in the hole and tapped the plastic pin with a small hammer into the support stud. Replaced crisper drawer cover and glass shelf. Easy fix

Followed instructions from others on the blog. Shut off water and electricity to the refrigerator. Removed the cardboard plate. Removed the old water valve. Cut the compression valves off and inserted the tubes into the new water valve. Attached the water valve bracket to the fridge. Tightened copper water supply.Turned on the water - no leaks. Plugged the fridge in. Tried the water and ice in the door. No leaks - everything worked perfectly. THANK YOU PARTS SELECT!

I replaced the water valve, but it still did not fix the problem.The old water valve I took out I'm assuming worked fine, I think the real problem is ice building up in pipe or some other blockage.

Parts select was very fast in shipping, very positive experience with them.
I will definitely purchase again from this site.

very easy to install...shipping was really fast...i would order to this website again....

Fantastic!
Sent in a brief description of problem and model number. Reply and description of other customers experiences guided us to the exact problem.
We ordered the part on Friday and it was here on Tuesday.
I prepared the freezer compartment for the removal of the old motor and on Sunday husband installed new Evaporator Fan Motor.

It works and is cooling like it did when it was new.

This has been a great experience as all repairmen wanted at least 60.00 to just come out and determine what the problem was. I can only imagine what the final bill would have been.

This was easy and inexpensive.

Thanks for all the help.

I simply unscrewed the original and replaced it with the replacement. It was very easy. I did have to order the label as the original one would not come off to be re-used. Hopefully, that will go on easily as well.