WRS23W0AW9 Westinghouse Refrigerator - Instructions

It was so easy, I just lifted the old one off and the new went right into place. No tools needed.

I was really impressed with how easy it was to navigate through your website and found the exact part I needed. I immediately received my glass shelf it took all of 2 seconds.

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Looked it up on how to, follow the video
. Very easy 1-2-3 it was out and new one in..........??.

Had to disassemble the entire ice maker bucket. Simple and straightforward, didn't need any pictures or reference materials. Just time consuming.

I watched You Tube on how to repair it the instructions that came were shit. I'm a stickler for wire colors being correct, could find that information in the instructions. Everything is on you tube I love you tube. The fix is is easy peasy. I'm not stupid eather there is nothing on that frig I could not repair if I can get parts even the compressor I can braze to. I know how it all works I never call repair people I will throw it all in the garbage if I can't get parts. That goes for TV's cars you name it. I have tools for all things.

Ice maker is held by 2 screws just above the unit, on the wall of the refrigerator. You can't see the screws, so borrow your wife's makeup mirror. Shine a light into the refrigerator, and using the mirror, locate the two screws, holding the unit in place, on the wall of the refrigerator. Using a nut driver, or socket wrench, with a 1/4 in socket, loosen up the two screws, but don't remove them. Bump the unit upwards, and away from the screws. (BEFORE doing anything!! Shut off the water supply, unplug the refrigerator) When you get the unit freed up, just unplug the old unit, and install the new one. You don't even have to worry about the water lines, and you'll see why, when you get the old unit off. Just reverse the procedure, installing the new unit. Very Simple, 10 to 15 minutes tops.

Loosened the 2 bolts 4 turns where it mounts inside the freezer. Lift maker off the bolts unplug 1 plug. Reverse to install.

just replaced old bins with new ones

Pull refrigerator from wall and disconnect the water line and unplug the power.

On top of the icemaker, two machine screws hold the icemaker to the side of the refrigerator. You will have to feel around to find the machine screws, but once you do, it is simple to slip the appropriate size socket over the hex heads. I found it helpful to have an extension on the socket wrench. Disconnect the power cable inside the refrigerator (there are little pressure clips on the side that help release the cable) and move it out of the way for the time-being.

Back out both machine screws several turns, but do not remove them completely. The icemaker slips over the screws, so leaving them in the side of the refrigerator makes that process a lot easier. Hand tighten the machine screws once you have positioned the new icemaker in place. One thing to be sure and do is make sure the water line hose coming out of the back of the refrigerator inside is on top of the icemaker. It fits into a slot in the top of the icemaker - failing to do this will result in water pouring into the freezer compartment, not into the icemaker..

Reconnect the power cable to the new icemaker and tuck it up behind the icemaker assembly. Tighten the machine screws completely, but do not over-tighten.

Reconnect the water line on the back of the refrigerator at the wall, and plug in the refrigerator. You should hear the unit fill immediately.

In about an hour you should have ice filling the bin. Enjoy!

The repair was not difficult because you just remove the old part and plug it in and connect two wires. But I wish there was a way to test if the compressor is working before I purchased the parts. The compressor would not start so I was not able to repair the refrigerator.

Remove ice pan below ice maker. Got mirrow verifed the type of screws. Obtained nut driver and felt it at right angle remove screws only have way. The ice maker lifts up and off. Took needle nose pliers to grip and remove electrical connection plug. The instruction and picture sent was no help the picture were the size of a thumb nail no detail could be determine. I installed the adapter plug and all the extra length wiring was the most difficult to type wrap with both hands extended out in front. I finally wrestled it in on to the two screws unscrewed from the wall about 1/2". Keep the ice maker water lever up and ensure it aligns to the water trough inlet. Works Great.
glg

it's very simple......take off the bottom plastic grate that catches the overspilled water, unscrew the 3 bottom screws, take off the black plate ( just lift up slightly), take out three more screws, then get the flashlight out. ......on top of the actuator, you will see 2 small silver-colored screws with very small silver-colored plates ( maybe 1/4 inch long), they hold the actuator into the unit. unscrew those and pull out the old actuator unit. You'll need to use your flashlight and pull the entire unit out to get access for replacment. Reverse the process for replacement, put in the actuator, screw in the 2 small silver-colored screws and there little plates, push the entire unti back into place, then screw in the remaining two sets of 3 screws......replace the faceplate and water grate and you're done.

I stuck a small screw driver under the old switch & it came out really easy. I just unplugged the 2 electrical connectors, and removed the old switch. Installing the new one was just as easy. I am a woman!

I also want to say how FAST PartSelect gets their items to you. It came in ONE day!

Your repair stories are very helpful, I/we would have never known how easy this switch was to replace! Thank you!

Removed the door marking the top hinge placement prior to removal. Pulled the door the rest of the way off. There wasn't anything keeping it attached on the bottom right side. Turned the door upright dug out the old broken cam and replaced it with a new one. Thank you for your web-site. It saved us $$$ you have gained two new fans to your web-site. I have shared your link with many. To to anyone who is having a popping noise when you open your door. Do panic. Log on to Part Select .com. It is your only source of sanity.

Thank you

Liz