WRS23MF5ASY Crosley Refrigerator - Instructions

All I did was remove the drawer, remove one screw. I took out the old slide, installed the new one and replaced the drawer. Quick and easy

It was so easy, I just lifted the old one off and the new went right into place. No tools needed.

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

It was as simple as removing two hex head screws to remove the old ice maker, then aligning the new ice maker (ensuring the downspout from the water supply was directed into the opening designated for it) and then screwing the two screws back into place. The most difficult part is the space that you have to work with. It was a little difficult and frustrating, but put in place, an hour later we had ice and it's worked great since!

I remove the old fan by pushing it off the spindle toward the evaporator and put the new one on by holding it on the right side and guiding it on the spindle from the left side, very easy task

Looked it up on how to, follow the video
. Very easy 1-2-3 it was out and new one in..........??.

Ordered new ribbon cable. At first I couldn't figure out how to get the wide end of the ribbon cable off, and I took the whole inner circuit board out - in fact, all it needed was more muscle, a straight pull out, no clips or anything holding it in other than friction. The narrow end attached to the control button board has two clips which pull towards you to loosen the ribbon. Easy install, worked perfectly

Followed Youtube video. Remove 6 screws, take housing out, and use finger pressure along with putty knife to remove damper from housing. Take note of where temp sensor lines route so the can be replaced the same. Only thing the video missed was mine had a filter on the ice maker line which required removing an additional housing (1 screw) and disconnecting 2 water lines. You need to squeeze the blue fitting on the water lines down to release the water lines and again to reconnect them after. Refrigerator is extremely quiet now and works great.

Loosened the 2 bolts 4 turns where it mounts inside the freezer. Lift maker off the bolts unplug 1 plug. Reverse to install.

Pull refrigerator from wall and disconnect the water line and unplug the power.

On top of the icemaker, two machine screws hold the icemaker to the side of the refrigerator. You will have to feel around to find the machine screws, but once you do, it is simple to slip the appropriate size socket over the hex heads. I found it helpful to have an extension on the socket wrench. Disconnect the power cable inside the refrigerator (there are little pressure clips on the side that help release the cable) and move it out of the way for the time-being.

Back out both machine screws several turns, but do not remove them completely. The icemaker slips over the screws, so leaving them in the side of the refrigerator makes that process a lot easier. Hand tighten the machine screws once you have positioned the new icemaker in place. One thing to be sure and do is make sure the water line hose coming out of the back of the refrigerator inside is on top of the icemaker. It fits into a slot in the top of the icemaker - failing to do this will result in water pouring into the freezer compartment, not into the icemaker..

Reconnect the power cable to the new icemaker and tuck it up behind the icemaker assembly. Tighten the machine screws completely, but do not over-tighten.

Reconnect the water line on the back of the refrigerator at the wall, and plug in the refrigerator. You should hear the unit fill immediately.

In about an hour you should have ice filling the bin. Enjoy!

Had to disassemble the entire ice maker bucket. Simple and straightforward, didn't need any pictures or reference materials. Just time consuming.

just replaced old bins with new ones

I stuck a small screw driver under the old switch & it came out really easy. I just unplugged the 2 electrical connectors, and removed the old switch. Installing the new one was just as easy. I am a woman!

I also want to say how FAST PartSelect gets their items to you. It came in ONE day!

Your repair stories are very helpful, I/we would have never known how easy this switch was to replace! Thank you!

Piece of cake! The new part just plugged in to socket and back into fridge frame. Appreciated how easy it was to order this part.

Removed the screws on the piece holding the switch which is at the front of the ceiling of the refrigerator box. Removed the old switch and replaced it. Very simple repair.