WRF535SMBM00 Whirlpool Refrigerator - Instructions

The rail & the drawers need to be aligned with each other & then push the rail into the little hole in the back wall of the frig while sliding the drawers in at the same time. I think I put too much fruit & vegs in the drawers which makes them heavy & the little tab which is there to support the drawers has broken off twice. This is the 2nd time I have ordered this rail. It would be helpful if the rail had a vertical supporting post towards the front. I like to have a lot of produce on hand all the time

Removed Left side support with broken pin (3 small hex head bolts). Replaced with new support with pin in place. Note behind: I broke the pin trying to replace the cover. Now I know to flex back the side to the cover, and not flex the pin which broke. This cost me 25 bucks and one hour, saving me from a probable $300 dollar charge. THANKS, PARTS SELECT!!!!!

Removed long drawer. Unscrewed the end cap. Removed slider from broken end cap. Reconnected the slider to the new end cap. Screwed new end cap in place. Replaced drawer. Done!

Remove all three drawers. Remove the glass panel. Remove screws from pantry end cap. Remove end cap from refrigerator. Remove temperature control assembly from old end cap. Install temperature control on new end cap. Install new end cap in refridgerator. install screws. Put glass panel back in refrigerator. Put drawers back in refrigerator. Install drawer lid on new end cap. Close the refrigerator. The part arrived within two days. The repair took a total of 20 minutes from opening the box with the new part to closing the refrigerator door after the job was complete.

Took shelves and crisper drawers out, took broken left panel out with nut driver and then replaced with new part. Installed drawers and glass shelf and finished.

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

This rail holds up the two crisper drawers.It was easy to select and order it on your website. It arrived in a few days with standard shipping instruction, and snapped in place in a few seconds.

I watched the on line you tube video on how to DIY. The putty knife worked to pop out the switch. I used the standar screwdriver to unplug the switch from the wire harness. Then plug in the new switch and pop it back in to the roof of the freezer. Tip: watch out when ordering the new switch - the freezer switch is different than the refrigerator switch. The freezer has three prongs. The fridge has two. I initially ordered the wrong part and added a week to the repair time and had to pay shipping to return the first switch.

Removing the large drawer,2 drawers,glass shelve & 2 end supports,two screws on the sliding track & two screws on the Pantry end cap it took me 15 minutes. When removing the left Pantry end cap on the right side, care must be taken because Center Crisper Rail #PS 162879 is attached to the Pantry End cap at the back & real care must be taken to remove it. After all the screws are removed pull the end cap carefuly towards you while moving all to the left until it clears the back wall of the refrigerator. Again, real care must be taken using a flat head screwdriver to remove the plastic track for the Center Crisper Rail. The Pantry End Cap on the left is a lot easier to remove than the right side.

The large pull out full width drawer cover hinge pin broke off on the left side. The repair is easy with just two tools, a 1/4" nut driver and a phillips head screw driver. I removed the two conventional drawers that sit above the wide drawer with the broken hinge. Next lift out the glass divider that sits on top of the wide drawer and set it aside and remove the two braces front and back by lifting them out of their respective grooves. Remove the wide drawer with the lid by pushing in on the two black clips on each side of the drawer slide up towards the front and pull entire drawer out while putting pressure on the two clips at the same time. The drawer should come out leaving the drawer slides behind. Unscrew the 1/4" hex screws on the broken side panel using the nut driver and gently pull the side panel straight back toward you. Remove the drawer slide from the broken piece by unscrewing the two phillips head screws and rescrew the drawer slide onto the new side panel. Replace everything in reverse order. One note: do not use too much torque on the screws when replacing the parts as they only screw into plastic, this will avoid them stripping out. A snug fit is all you're after. There now, go pop a beer and sit down and relax, you are now a refrigerator repair man!

Remove two upper trays. glass shelf and shelf brackets. Remove bottom tray. unscrew side with back vent openings and remove with humidifier controls attached. Carefully remove control arms and back vent cover. Install on new unit and screw back in place. Check to make sure hinge pin lifts drawer top properly.

This was a very simple repair. It took longer to remove the crisper bins than it did to repair the pantry end cap.