WEF326GSA Westinghouse Range - Instructions

Pulled stove away from wall and unplug .Removed grates for better access. Unscewed element scews removed element & tested for continuity.there was none element is bad . Replaced with new one . Time about 20 minutes.

Removed the back panel, disconnected the terminals and removed the old one and installed the new one.

The elements tested good. Figured it was the electronic clock timer/control using the sites repair guidance and ordered the part. The remove and replace was very easy. Pulled the stove out, removed back panel and removal and replacement of the part is pretty basic. Be sure and unplug the appliance first. Everything works fine now.

Took the drawer out, snapped the new glide in place, and replaced the drawer. Installation was simple with no tools required.

Unplug the stove or disconnect at the breaker. Open the oven and remove the bake racks. Using a nut driver (or Phillips Screwdriver) remove the screws (one per side) that secure the bake element. Place them in a safe/secure place outside of the oven. Carefully pull straight back on the element until about 3 inches of the wire, that connects to the element, is exposed. Carefully unplug the wire from each element (make sure that the wire does not pull back into the oven insulation. I placed a small metal clip on each wire). Remove the old element and plug the new one in. Put everything back in the exact same way you took the old one out. Power the oven up and preheat your oven. Monitor this - should be no problem at all. Very simple process. My first attempt at this and it was very easy.

With the draw glide, I simply had to slide it into position. To replace the clock, I had to remove the back panel and then replace the broken clock with the new one by simply turning a few screws and using a pair pliers to removing the color coded wires.

First we turned off the electic, then we took the back off the stove and pulled the wire off the bad element then replace the new element. It was very easy to do.

First I removed the oven door from the range by removing 2 screws from the door. Next I removed 2 more screws from the oven door to get to the panel beneath. Once the top portion of the door was removed there were 4 nuts holding the glass sections together. Once these nuts were out I removed the broken class, replaced it with the new glass and reassembled. It was a very easy and quick project. I was so happy to find the part. I thought I was going to have to buy a new range. Thanks.

Unplugged the stove first !
Removed bake element ; (2 screws), looked OK,
measured with an Ohm meter, measured "open".
Also, removed rear cover (6-screws), wires not burnt. Ordered new element-rec'd next day! My wife installed it and replaced rear cover. Works great (oven!) and about $10 cheaper and quicker than from a local dealer!

Got a copy of the parts breakdown for the oven door from partselect. Com. Removed 8 screws from outer frame (3 top, 3 bottom, 1 on eah side). Removed the main glass pane from oven door, be careful when doing this as this is most of the weight of the door. It will want close on its own due to lack of weight. Removed the 2 top screws that attach the handle. Removed some screws from some plates that retain the 2 panes of glass of glass. Removed the third (most inner, broken) pane of glass. Replaced with new one. Reversed disassebly procedure for assembly.

Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience with those in need of you services. Thanks. Marilyn Kasson

I had open back cover and remove the switch than replace new switch. Makesure cable conection.

I follow the video on your site

Screw the handle, that it...

All you do it unplug the old one and plug in the new one.