WCRE6270H1WW General Electric Washer - Instructions

Followed video to take washer apart. I used the Shaft & Drive Assembly to tap out bearing as it was stuck. BTW the screeching was because the Shaft & Drive Assembly ball bearing retainer cage was in pieces. Replaced tub bearing and installed new Shaft & Drive Assembly. Washer now runs like new. Get the spanner wrench to remove existing nut and purchase a new nut.

I happen to be a mechanic so the repair was quick and saved me from buying a new washer! But the step by step videos yhat come with your parts are very easy to understand . This company has saved me thousands of dollars on new units or calling a repair company

First buy the tub nut wrench. I can't over emphasize that! $12 at amazon. With out it getting the inner tub out will be the worst part of the job. And you will have to buy a new nut. I had trouble getting the old bearing out of the outer tub. I had to drive it out with a punch. The only other problem I had was after getting everything back together the new tub seal leaked. When I installed it if fit very loose on the OD. I ordered a new seal hoping it would fit tighter but it didn't so I coated the the seat of the tub and the OD of the seal with gasket shellac. That solved the problem. Working great.

I watched the video and disassembled the machine pretty much the way the video showed. There were a few differences but nothing big. The noise sounded like a dry bearing but wasn't sure where it was. Read the responses and it said it was the tub bearing washer. It made some sense if it was metal on metal. It was a dry bearing (should have listened to my common sense, but these guys know more than I do when it comes to washer repair) on the transmission that had been ruined because of a leaky tub seal, which I also replaced. The transmission was not available at the time of repair (but is now) but that kind of investment may be better in a new unit. There is a video on YouTube that shows you how to replace the bearing, BUT it requires someone with some mechanical knowledge. I'll try it later in the year and if it doesn't work we'll have to purchase a new unit.

Followed the video guidance supplied by this site

I had to insert a broom stick to keep the drive pulley from rotating as I hammered the tub nut loose.

2nd tip, my washer has the standard agitator with the glued on cap; it was unclear if I needed to remove it; you should clarify that this is not necessary, that one must only pop up the entire agitator; I used a shipping strap looped under the agitator and over a 2x4 across the top of the frame, tightening until the tub was raised a bit and then a gentle pop down on the tub and the agitator easily popped off.

Lid Switch.
Rewiring connection.
Function is satisfactory.
Fan belt ordered is saved.
A 1970 Clothes Washer.

We took off the selector knob that was on the washer and you could tell one of the feet was broken. We then ordered the knob and a number of other items in case it was not just the selector knob. We were lucky because it was only the knob. We pushed the knob into place and it works. We did return the other items. The other items, pressure switch and electronic control board, were suggested by the website in case we had a bigger issue. We ordered all up front so that once we took off the selector knob if we had the other issues we would not need to wait for parts. Thank you for having parts available and sending them in a timely manner and also helping with the return of parts.

Removed the front cover with a screwdriver, by locating and slightly prying the metal clpis back to release the cover. Then I removed one screw (only one visible) from the strap that hold the top cover/lid down. With a little prying, I lifted the lid up out of the way, and suspended it with a cord. I removed the old dampener straps and replaced each one at a time with the new strap. It was not to hard to get to the screws (I have large arms), and it only took me nearly a half hour to complete the task. It would have been easier if I used two different size nutdrivers, but it was easy enough with an adjustable wrench. Then simply put everything back to together in reverse order of how I took it apart. The wife was impress that I fixed another thing around the house.

Removed the two hex head screws from the broken strap and replaced it with the new one. The other three straps were not broken but I also replaced them, again, one at a time. This made sense,since the machine was at least ten years old.

Wife put on the new part and she used a pair of plires and it was a little difficult to get her hand in the tiny spot but she put it on in less than 15 minuets and it is working great.

Could have removed debis in old pump. Kept it as a spare.
Replacement was simple , (two nuts) & (2 Lg. Hose Clamps) + two wires.
Dealer wanted $168.00 Labor + $67.00 for part!.

I pushed a small screwdriver under the top lid and pulled the front out and lifted it out or the way. The rubber hose had two clamps holding it. One you loosen with a flat screwdriver and the other one you squeeze with pliers to remove hose.Then replace hose and put front back on. It's very simple.

Surprisingly easy. I took the screws off, then pulled off the drain hose. I then inserted the new hose, and put back the screws. Amazing quick!

Unpacked the agitator from the box. Manually pulled off the old agitator and snapped on the new one. Total repair time was under 2 mins. Much better than a $120 service call.