Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Hose had developed a slit in the seam nearest to the tub and was pouring out the water flooding the basement where the washer is located.
Lay the drain pipe lower than the tub to remove any excess water in the tub and lines. Loosened clamp on the tub side with a screwdriver then removed hose from the tub. I used pliers to pinch clamp and remove hose from pump. To install hose put clamps on hose then mount to the pump and the tub then tighten clamps.
turned washer on it side took bottom off removed hose and replaced it with the new one. so very happy i tried it , works great like before. thanks for the easy to find diagram of parts.
first I filled the washer max load to determine the problem, once I saw where the water was dripping I decided to remove the hose. I removed bottom of the hose, and the water from the tank started pouring out, I tryed to put the hose back on but started to get a pretty good electric shock, I then unpluged the washer and ran to garage for the floor squeegy. I then pushed the water out the side door. After cleaning and drying all rooms I sat down at the computer and ordered part. When the part arrived I removed clamp with pliers put both clamps on the new hose and installed. A very simple project and I ended up with a clean laundry room. Thanks "Brainy"
I pulled the front off of the washing machine using a table knife to pop the clips. The drain hose had a hole big enough to put your finger in so we knew that was the problem. One of the clamps holding it on took a screwdriver to loosen the clamp, the other I used a pair of adjustable pliers to squeeze the ends together to loosen it. I pulled off the old part, ordered it, got it the next day and replaced it the same way I took it off. It was simple and the part was less than $10.
"Thought" the belt was the problem - ordered new belt - waited for belt to arrive - opened washer. Belt was in perfect condition - problem is the clutch. Next time husband will verify problem before ordering parts.
Changing the belt didn't solve anything. We took the console apart and there is a Troubleshooting Guide folded up in there. It has a Code List and a sequence to follow to determine the trouble codes. While there was nothing wrong as far as coding, it did lead us to confirm the discharge pump WAS working, even though there was no water coming out. The discharge hose was plugged.
One of the paddles broke from washing something that wedge in between one of the paddles and side of tub. Which broke the blade. Order the the part from Parts Select. Watched the Video how to change the Agitator. It was as easy as they said. Repaired it myself for least than $50.00.
Pull the Agitator out by hand no tools where needed. Took Fabric Softer dispenser off put it on new Agitator. Pushed the new Agitator on. Repair done. Sure am happy I did it myself. Service charge from repair company would have been a lot more then $50.00.
The belt is very tight. Use a zip tie to old the belt on as you work it around the large pulley. Once it is on remove zip tie and turn the pulley enough times to line up the belt evenly then your done.
Couldn't get the agitator off by pulling up, then thought about it and got 2 carpenter claw hammers, inserted one on each side and puled up evenly on both and off she came. Sprayed the slots with WD Forty and popped the new on. THANKS saved us a lot of money!!!
Step one: Order the Belt and the $10.00 tool that fits on the motor sprocket to keep the belt from slipping off. Step 2: Lean the washer back at about a 45 degree angle, you may have to disconnect the water lines to achieve this. This puts the machine in a good position when you sit in front of it as you are installing the belt. Step 3: Install the tool over the motor sprocket leaving the grooves exposed. The belt fits in these grooves. Step 4: Slip the belt over the motor sprocket first and than the large sprocket wheel behind. This will take a little muscle as the belt is considerably smaller. After a couple of attempts at rotating the big sprocket the belt kept slipping off. I than took a plastic tie and strapped it around the belt and the big sprocket wheel, this kept the belt from slipping off as I rotated the wheel. Once the belt is on snip off the plastic tie and you are home free.
I searched the internet for the problem resolution & purchased $40 of the parts before I disassembled the machine. This was to minimize the downtime. Not one of the internet sites recommended changing the shaft & mode shifter assy so all the parts I ordered were not needed. Once I determined the correct part I had the reorder & pay expediting fees to deliver next day.
After watching the YouTube video on how to disassemble the GE Profile washing machine the repair was relatively simple.
The washer had quit agitating but was still spinning
This job did not take much longer than 15 minutes if that.1st take the cord or twine and loop it under 2 paddles of the agitator.( there is a small groove under each of the paddles that has enough space to put the cord in) Pull up on the cord to remove the agitator. 2nd. Under the agitator is a bolt that secures the agitator coupling. Remove that bolt. Keep bolt(you may want to replace this bolt if rusted and worn. Mine was still ok so I reused it.) 3rd pull up on Agitator coupling to remove. Teeth were worn on Coupling, So discard. 4th Insert new coupling, replace bolt to secure coupling. finally slide agitator back over coupling till locks back in place. ....Done.
I was frantically trying to find a cheap washer to replace the one that "broke". Fortunately, my son's roommate is a maintenance technician. He diagnosed the problem immediately. I googled the issue, found the part, ordered it and received delivery of the part in 3 days. It took all of 5 minutes to replace the part and reassemble the washer. Now on to the 15 loads of laundry that have been stacking up!
Inside the appliance is an instruction sheet that describes replacing the part and followed it mostly. To improve your instructions, pictures with the instructions are much more effective and easier to understand.
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Was this instruction helpful to you?
Thank you for voting!
Nothing bad, just a VERY tight belt.
Take front of machine off, unscrew bottom and lay out just enough to get under the machine you do not have to take it completely off. After that unscrew center bolt holding wheel and wrap belt around then attatch the belt to the power spinner pull down as best you can and reattatch the wheel and bolt back up.
