TRS20WRHW3 Tappan Refrigerator - Instructions

Tested for power and found the thermal cut-off bad. Installed new one.

Removed front panel out of existing drawer, it slid up and out, slid it into new drawer, drawer was as good as new!

followed the video very esay

open freezer door two screws just below unscrew slide piece to side unplug reinstall very simple.

I noticed that the two gears weren't meshing together so upon inspection I saw that one of the gears had an inner piece missing making it weak so it kept popping out away from the other great. I ordered the new gear and unscrewed the old one off and put the new one on. So easy. It made Ice beautiful after that

I followed the advice of many people with the same problem, and replaced the Defrost Thermostat and Defrost Timer. Both repairs were relatively easy, and the problem appears to be solved. The replacement of the Defrost Timer is very easy (about 30 minutes), and I wish I had stopped at that step and waited 48 hours to see if that fixed the problem. But, I wanted to replace both parts that I had purchased - - In my refrigerator, access to the Defrost Thermostat is through the back of the freezer panel. Not too difficult to get to the area, but I had a bit of a problem in replacing the part, and might have been better-off to see if step 1 fixed the issue. The problem that I ran into is that I don't have a crimping tool, and crushed both of the connecting sleeves when trying to 'crimp' them with a set of wire-strippers. Rather than to invest in a crimping tool, I connected the wires and sealed with electrical tape - - Now that the issue is resolved, I will likely re-open and use a proper connecting sleeve (with a proper crimping tool). My advice is to buy both parts, and replace just the Defrost Timer first. Chances are good that it may fix your problem, and you are only out $20 for the second part, which you can leave in your junk drawer until you may need it some day! All in all, it was a great way to spend $40 and avoid a costly service call!

After some troubleshooting to ensure the thermostat and heating element were working, determined that the defrost timer was the problem. With the defective part, I was able to manually advance the timer to activate the defrost cycle, but it wouldn't do so on its own. Unplugged the refrigerator from the wall. Timer is located in the refrigerator compartment at the very top. The compartment houses the cooling thermostat, the light bulb and the defrost timer. Using 1/4" nut driver, remove 4 screws holding compartment cover to top of fridge. Lower a bit to access electrical wiring. Wiring harness can be unplugged to work on the timer away from the fridge which makes it a bit easier. Timer is mounted with 2 phillips head screws. Remove screws and unplug timer from wiring. Install new timer, plug in wiring, secure with the phillips head screws and remount entire compartment.

I watched the video and it seemed pretty easy. I ordered the new ice maker. It arrived in 5 days and I chanted it in less the 30 minutes. A little tricky seeing where you have to loosen the screws but not hard. and in 2 hours I had ice again.

Watched the video once. Removed four 1/4 inch screws with a nut driver unplugged the unit, took out two screws securing the timer. Replaced did all of this in about 10 minutes. It was "exactly" as the video showed and it's worked perfectly since the replacement of the faulty timer. I saved a $75.00 service call minimum and the part was more than likely cheaper from Part Select than from the repair facility. Although I'm a pretty good handy man, you would not need any experience to make this repair. The instructions are precise and the part fit perfectly.

Make sure the drawer is very clean and there is no residue at the base of the drawer. If needed put very hot water in the drawer to disolve any gunk. Then pry the lip on the reverse side of the drawer with a screw driver. then the front will slide up and come off easily. If the drawer has any gunk in it, the front will not come off.

Simply replaced the defrost timer located inside the frig just behind the temp dial. Very easy job. Removed the 3 screws holding the temp sw and light assembly. Removed the defrost timer w/ 2 screws and put i all back together. 15 mins at most. Suggest you watch the install video for pointers.

replaced broken end cap

first copy the explored view of all the parts ' ice maker tray ' then just take it apart slowly you need to get the blades back in the correct order and position thats what the exploded view is for in case you forget then you replace the blade and reassemble , it take a good hour .

Purchased a new ice maker assembly and installed. Very easy

I snapped the brackets into the ends of the shelf bar, then inserted them into the holes in the door and pulled down each end until it snapped in place.