Quick Question!

Have you ever purchased from PartSelect.com before?

Models > TC607S0 > Instructions

TC607S0 Jenn-Air Trash Compactor - Instructions

All installation instructions for TC607S0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the trash compactor repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TC607S0
31-45 of 148
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broken gear

  • Customer: Francine from bowie, MD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 3 of 5 people found this instruction helpful
Unscrew the bottom, pull out the chain, replace the gear.

compactor wouldn't shut off

  • Customer: Ray from Dallas, GA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 2 of 3 people found this instruction helpful
changed out the switch and that fixed the problem

Compactor piston stuck in down position and couldn't open!!!

  • Customer: George from Houston, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 2 of 3 people found this instruction helpful
First thing I did was put the unit on its side and removed the bottom to access the broken plastic gear that moves the chain that drives the compactor up and down...There I was able to manually move the chain by turning the nut with pliers and moving the piston up (painfully slow) until I could at least use the bin for trash while I waited for the replacement part to arrive. Once I had the part I loosened the four bolts that allowed the drive gear to move a little and slacken the chain - I then put in the new gear - make sure you have the proper spacing and washers - my replacement kit didn't have any washers so I resused the old washers and all seems to be working well!

The compactor rubber guard was torn.

  • Customer: Judith V from Studio City, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
Removed 4 screws and the foot release to attach the new guard. Replaced the foot pedal and 4 screws and was done.

Trash carier wore out

  • Customer: Carmen M from Port Orchard, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Upon the receipt of my part it just had to be slipped into place. I had the part I needed within 3 days of ordering.
My had ordered parts for various items in the past and we have always been very satisfied with the care and experteis of this company.

lost cover (went into trash)

  • Customer: Jacek M from Bedford, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 6 people found this instruction helpful
replaced

Jammed KitchenAid Trash Compactor.

  • Customer: Jan from Gilroy, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench (Adjustable)
  • 2 of 4 people found this instruction helpful
With nothing in the KitchenAid Instructions nor anything on the internet… I had to go it alone.
Actually quite simple… I laid the unit over on its front and removed the 5 screws holding on the bottom plate. This exposed the motor and drive train which turns the two compacting screws on each side. The main drive gear was broken.
Taking a wrench to the main drive… I was able to free up the jam… a piece of glass from a broken bottle.

I went to the internet and did a search on KitchenAid Trash Compactor Parts and discovered PartSelect.com… They had me enter the Model Number of my unit and a parts diagram and list came up… I found the gear I needed… ordered it and in two days it was here. Instructions came with the gear on replacement and in no time I was back in business.

I was impressed with the simplicity of KitchenAid’s Compactor, and the ease in which I was able to get my part from PartSelect.com!

Smelly kitchen

  • Customer: Saralyn from Dahlonega, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
Removed the old filter and screen and replaced with the new!

Plastic Drive gear broke

  • Customer: Terry from Spring, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 2 of 4 people found this instruction helpful
The plastic drive gear broke and the unit was locked in the down position. The repair kit contained all of the parts required to fix the problem plus other replacement parts for the gear drive unit. It was very easy (about 20 min.) to replace the gear and other parts. The unit works fine now.

Trash plunger would go down but not back up

  • Customer: Mark from Westport, MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
Compactor ram would go to bottom but not return back up after compaction. Keep running until unplugged. After unplugging flipped unit on its side and remover bottom plate (5) nut screws, exposing gears. Found that the main large gear had fine crack which caused it to spin loosely. Ordered gear assembly and lossened four mount screw on motor to move it forward and give slack on chain. Hint: Loosen motor mount bolts, DO NOT REMOVE bolts COMPLETELY! Removed broken plastic gear and reassembled with new. Held/ pushed motor back to retention chain and secured four (4) mount bolts Then reassembled bottom plate with screw nuts and it worked perfectly!!

Actuator broke off ordered new one

  • Customer: avi from WOODLAND HLS, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
Step one-read instructions; step two-follow them! Really not that hard. Pull the compacter out. Take four screws off the top plate. Take 8 screws out the face plate. Disconnect old actuator install new one. Put the cutout over the new one. Drill ONE hole with template. Screw the one in. Now drill the second hole out-but make sure its level dont be a tool and make it all crooked. Then screw it in place. Put the face plate back in with the 8 screws and put the top plate back on. Now remove foot assembly and old actuator lever from drawer. Install new rubber thing a bobber and put the foot assembly back together. Put it all back in smack it with a hammer 32 times add duct tape and voila donzo!

ram would not go up and down gears went bad

  • Customer: Elbert from FRANKLIN, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
layed it in the kictuchen floor took of bottom and changed the gears that's all there was to it piece of cake

Compactor would only stop and reverse if you turned it on and off. Very noisey.

  • Customer: Bill from DERRY, NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
First let me say that I read many of the other posts regarding this repair and without them I wouldn't have had a clue how to fix this. Since the ram apparently moved up and down when I shut it off and turned it back on I reasoned the directional switch must be the problem. Ordered the part, Quick delivery. To replace the switch I removed the draw and removed two screws on the frame that hold the control panel in place. Lift up to remove. My unit is a stand alone unit although it is installed under the counter. There are two additional screws to remove the top and expose the ram and power screw drives. To remove the directional switch from the control panel you need to remove two hex head screws that hold it in place. This is a little difficult because of the small space. With the help of a small nut driver I was able to remove it. Note: the screws are held in place by a flat piece of metal that acts as a nut. Be careful not to drop it. Then simply remove the wire leads (all color and letter coded) and remove the switch. I was careful to reattach the leads to the new switch as I removed each one. Be sure to replace the switch with the limiting lever in the same position as it was in (it is vertical). Put everything back together and you should be good to go. That didn't happen for me! Problem persisted! Next on my list was the power nut. I got access to the ram and power screw drives (see above for instructions). The two power nuts are plastic wing nuts that are held in place by metal covers. The metal covers are each held down by two hex head screws. To gain access to the power nuts you have to remove the metal covers. Note the position of the nuts in relationship to the power screw shafts so that when you reassemble it they will be in the same position as when you started. In my case the top of the screw shafts were even with the top of the power nuts. (CAUTION: the ram is held by this assembly. Depending on what position your ram is when you started this repair it may fall! My ram was in the up position and when I removed the second cover it slammed down to the bottom of the drive screws). My advice is to be prepared by bracing up the ram before removing the metal covers. No harm when the ram fell but it did startle me. I then removed one of the power nuts. It was split in half. The other nut was fine but I decide to replace it anyway. Ordered parts. Quick delivery. Before I attempted to replace the power nuts I removed the ram (it just lifts out) and cleaned every thing. I put some new grease in the places that I had removed it. Then sprayed WD40 on the power screws. When I put the ram back in, I broke the new directional switch I had put in. So be careful!!! I still had the old one so I ultimately put it back in. I then replaced the power nuts. This was a little difficult because I had to hold the ram up while I was putting the metal covers back on. I would suggest you either brace the ram or get someone to hold it while you put the metal covers back on (In retrospect I suppose I could have just put the nuts on when the ram was down). Reassembled everything. Should be good to go. That didn't happen for me! Problem was still there! I turn it on, ram goes down. I turn it off, ram goes up. Desperation!! The only other thing it could be is the drive gear assembly. Ordered parts. Quick delivery. The gear drive is on the bottom of the machine. Lay the machine on it's side to gain access to the bottom cover. There are 5 hex head screws that hold it on. Remove screws and cover. It's pretty simple from here. The drive gear was missing a few teeth but the rest were in tact. This explains why the ram was still moving up and down and led me to believe it was something other than the drive. The only difficult part was the removal of the pin in the drive shaft. I wound up using a bolt the about the same diameter and a hammer to drive it out. Then just reassemble. There are some instructions that come with the gear parts that tell you how to set the spacing in the gears but I had no problem just replacing the parts without making any "adjustments". Should be good to go! Yessssss! Everything worked perfectly!!! My final words of advice. If your machine has this problem CHECK THE DRIVE FIRST. It the easiest thing to do because you can visually inspect it and know or eliminate it as the problem. It's about a 5 minute job and can may save you some of the problems I had. A big thanks to PartSelect for sponsoring these posts. The repair company that I normally use told me the machine was too old and probably wasn't worth the $100 just to come out and look at it, never mind the additional cost to repair it. All in I spent less than $100 and had I checked the drive first, I could have been done for less than $30.

Trash bin would not roll out completely

  • Customer: Roger from Grantham, NH
  • Difficulty: Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 1 of 1 people found this instruction helpful
-Removed the forward sliding rail screws...lifted the rails up several inches to access the wheel assembly...bent back the steel tab to access the nuts holding the wheels to the frame...replaced the wheels and bent back the steel tabs to original position. Trash bin now rolls out completely as before

Would have been nice to have known that the replacement switch operated in the opposite fashion from the original switch. Also, kit was missing the two screws to attach the new lever operator.

  • Customer: John B from ARDEN, NC
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench (Adjustable)
  • 1 of 1 people found this instruction helpful
I had expected to just have to install a new spring steel "L" shaped switch operator to replace the one that had broken off. Installation of the new switch and redesigned operator was difficult in tight quarters. Good news, four hours later compactor works as advertised. Hope that the revised design works well and for a long time.
All Instructions for the TC607S0
31-45 of 148