TAA400 Amana - Instructions

I followed video instructions which were very helpful and getting to the lid switch assembly was not difficult. After putting it on we still had nothing. I noticed there was quite a bit a corrision on the connecters so we cleaned those with fine emery paper, reconnected them and like magic , the washer is back in business. I was very surprised the part arrived about 36 hours after I placed the order and in just a couple of hours at the most we had a working washer again.I've got partselect.com saved in my favorites for any future diy repairs needed.??

Started with removing 4 screws on the top of the control panel. Once open, I found the schematic taped to the top. I traced the wires and found the 2 wires to test. I unplugged them and attached the jumper wire. Turn on machine and it worked. Ordered the part( it came in in about 3 days. First disconnect the power. The micro switch is mounted with 2 screws, remove these and as you disconnect the wires , attach them to the new switch, put it back in place and reattach the screws. Test .

First I took the seals out of the box they came in and let them hang on a hanger to get all the kinks out of them for a few days. Then I started at the corners of the refrigerator doors and peeled the old seals off on one door then replaced the seal by using my thumbs pushing at the corners first and once I had all four corners in I worked my way around the rest of the door, After both doors were done I used a hairdryer to expand the seals against the refrigerator case to make sure it seals tight.

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

I watched the video suggested by Part Select, it was easy to follow. I had first changed the belts because they were worn but that wasn't the problem, the next suggestion was the lid switch assembly which was the answer. This washer was produced in 1989 and works like new again!

Done a troubleshooting problem online. Figured out the problem and ordered the part. Removed old part installed new part and I am a female not that it should make a difference but some would say it does. Had the old part out and new part put in and it took me about 30 minutes. Washer now works like a new machine. Very pleased and proud of myself. The part was the lid switch assembly.

Found instructions at this web site, got part in a couple days, changed Lid Check Switch in 15 minutes, washer was up and running again. Best website for fixing stuff I've seen!

had to completely disasemble whole washer drum and mechanical components to remove upper bearing on transmission,the drum hub was corroded on the shaft. I had to use a gear puller and a propane torch to get the hub off upper shaft of the transmission. then press the bearings in the respective sheet metal supports. reassembly was alot easier than taking it apart. Not a job for an average homeowner. It would not have been repaired without the wheel puller. all the seals were reusable A week and a half of use later no leaks and works great

Followed video on PartsSelect website, they made it real easy.

At first, I suspected the timer. In the problem solving section of the Maytag owner's manual, there was a reference to the Lid Check Switch, which was the queue I needed. with the help of the electrical diagram, I located the switch,then hotwired that circuit to confirm to myself that it was the switch that was faulty. Overall an easy fix.

I saw on internet that it was the lid switch and how to fix it. On this machine I have replaced timer and belts, machine is 22 years old.
A bowling friend of my father, was a Magtag repairman and salesman. For years showed me how to fix my Sears washer and dryer. When he sold me a Magtag washer and dryer, he said it was a great machine.By the way my dad worked for Easy Washer in Syracuse, They invented the spin cycle, ask Whirlpool.
ED

I guessed that the lid switch was bad based on internet information that suggested that cause of the problem. I confirmed this by disconnecting 2 wires to switch and taping them together to bypass the switch. Wiring diagram was available. Washer worked that way so I ordered a new switch which arrived within 22 hours, regular shipping.

Replaced the switch. No need for me to add detailed instructions for this simple swap. More than enough descriptions are already collected on the excellent website of this outstanding parts supplier!

Disassembled washer as per directions with seal kit. Removed inner tub. Cut both tub shaft bearing in half; punched out from outter tub. Installed new bearings using .5 inch threaded rod, washer and bolts. Installed new seal on inner tub shaft. Installed inner tube. Re-assembled washer.

We did not have instructions on how to remove broken agitator. Looking online, we found easy instructions but found it difficult to remove the agitator even though it was supposed to be an easy task.
Our particular model was supposed to "pop" off with little resistance. Not so!
It took some stong muscle and will power to remove the part but putting the new agitator on was simple.