Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Over the years the filter became too clogged with embedded particles
Really simple. You pull out the drain filter plate and pull the filter off the support and replace. I gave everything a good cleaning and put it back in place.
Got the wrong part.......NEVER got an answer to my 3 emails to customer service to find the correct part
I ordered the wrong part....needed their help to locate the correct part. Sent 3 emails asking for help to the 'customer service' email ----NEVER heard a word!!!......and now they want me to rate the installation ?! Horrible customer service
Bosch Dishwasher repeatedly reporting error E17 after a few minutes of running
Fairly easy repair, with the hardest part getting the appliance out of the cabinet. Kill the power and get the dishwasher out. Once out, the water inlet assembly (a large, white, opaque plastic box) is on the left side of the dishwasher, exposed and surrounded by the sound insulation. Pull back the insulation and use pliers to disconnect the small, white water inlet tube (hard to remove, you may need to pry a bit with a flathead screwdriver). Once that's off, look on the back left of the dishwasher for the valve access, which is mounted on a plastic snap-in tab. It was easiest to snap this out by reaching into the dishwasher from the side and squeezing the tab on the assembly with my fingers. Once it's out, remove the electrical connection from the old valve access by squeezing the tab. Unscrew the incoming water hose (from water service), and squeeze the clamp to remove the smaller white hose. Then go in reverse to reassemble: connect the white hose to the valve access and clamp. Connect the water service (make sure the threads take and it's solidly hand-tightened). Connect the small electrical plug. Snap the panel back into the back of the dishwasher. Connect the small white hose back to the water inlet assembly on the left side of the dishwasher and clamp. Test if you can, then put insulation and appliance back in. This totally eliminated my E17 errors.
Turned off power and water supply. Pulled dishwasher out. Disconnected the water inlet from the back left side. Swapped out the inlet valve. Wiped up the water in the bottom pan. Put dishwasher back and turned on water and power. Simple.
The washer had an error message in the display of E:09. I called Bosh on customer srevice and she said that the heat pump was not working and needed to be replaced. Since the motor is the main part for this that needed to be replaced as well. The pars were under $200.00 total so we oted to fix this
We followed the video and had no problems with leaks at all afterwards. The parts fit perfectly and the machine is working great again.
replacing the sensor was simple, just unplug and turn it out, but didn't solve the problem, it's a float sensor that doesn't show up on the tech sheet in the dishwasher or anywhere in troubleshooting on the internet I could find.
A rat got under the dishwasher and chewed up the electric’s and the hoses
A rat got under the dishwasher and chewed up the electric’s and the hoses. Only found out when the air light came on drain not working Lots of water underneath as well as all kinds or shoot insulation and rat droppings had to wear a mask affect him use a bunch of Clorox before I could diagnose it a real party And hard to reach corners. I ordered four parts since I found a better deal on the main electric cable which a rat head chewed through until it had an electrocuted itself. These four parts came in three different boxes and three different deliveries over two weeks. not efficient. But handwashing is over put it all together and it works I soaked the hose in hot water so I could fit it on.
Initially, I received an E15 error. I evaluated for leaks but couldn't find anything except for water in the bottom of the dishwasher after about 30 minutes of the initial cycle. After discovering the hole in the flow tub, I order the part. It came a few days later & replace the part within a 15 minutes of receiving it. I didn't think it would resolve the issue but it did. Thank you!
Inlet valve was leaking water at all times causing the unit to shut down with the bottom tray collecting water.
Repair was simple once the problem was diagnosed with the inlet valve. Most of the work was in disconnecting the necessary lines so the dishwasher could be removed from the cabinets to replace the bad valve. Replacing the valve was easy. Reinstalling the dishwasher was just the reverse of the removal. The replacement part matched the original and solved the problem we had.
Water leaking and high pitch noise mid way through operation.
Mistakenly opened covers for the drain pump. Had to put those covers back in place. Heater and pump installed easily with a bit of careful maneuvering the plugs and plug housing from the exterior. Pump installed in place easily. Clamp fit perfectly.
Top arm water connection to rear wall - all seals eroded and leaking
Removed the middle basket and turned it upside down. Unplugged the spray arm from the middle basket. Snapped the new spray arm into the middle basket. Installed middle basket into slides. It works great. Great site for parts - reasonable prices too
