SGR641HS1 Westinghouse Dryer - Instructions

Printed out what others said, took pictures of everything as I took it apart. I went slow. It all worked the first time I put it back, WOW!
Be careful if you are working with a gas line, use two wrenches to disconnect, less stress on the pipe.

first turn off breaker and unplug dryer !!! popped open top of cabinet pushing in on 2 clips with butter knife then removed the front panel,2 phillips screws then pull out on top until 2 spring clips pop out, remove 2 wires from door switch move to side. remove motor access panel lower rear 2 phillips screws. unplug wire clip from motor, push belt tensioner to right,undo belt from motor pulley and tensioner , then undo 1 snap clip from cradle holding motor go to front of dryer remove 2 phillips screws from blower houseing to base. unscrew senser from front of houseing then carefully lift slightly on front of drum and pull blower houseing and motor out as one. hold motor shaft still and unscrew blower wheel from motor shaft, install new motor do not overtighten blower fan you will break it slide belt off drum put new belt on makeing sure grooves are against the drum. slide motor assembly back in put motor back in cradle in rear and reinstall clip, screw down blower assembly in front, reinstall belt on motor pully and tensioner and clip wires back on motor. put front panel back on making sure not to damage felt on front of drum, rotate drum by hand several full turns clockwise to make sure belt tracks properly, reinstall wires on door switch and all screws and rear cover plug in turn breaker back on and test

Taking off front of and top of dryer and panels on the back. Releasing the belt and taking out the tube un screwing the two pieces off the back of the machine putting new ones in and putting belt back around drum and setting drum in. Then holding drum while the front is put back on then attach top and a couple panels on the back.

Easy - Pull off the old timer knob and push on the new one

I opened the pkg. and pushed them on!

I opened top section with a screwdriver, pushing in the release.
I opened front panel with door with screwdriver pushing in the release.
I lifted drum out through the front.
I replace the Idler Arm assembly.
I greased the rear drum bearing race.
I vacuumed out and cleaned blower and dryer area.
I put the new belt on the drum, reinstalled the drum.
I put belt around drive motor and Idler arm assembley.
I put front panel with door back on.
I put the top panel back down and snapped into place.
Tested dryer, job done!

It is so great to be able to turn my dryer on now without using my bare hand to turn the shaft that the knob was to go on. Nothing needed other than pushing knob in place. I so wish I had thought of looking online for a replacement part 4 years ago. Thanks!

Extremely easy. From finding the part on the website to installing on the machine.

I ordered replacement knob for washing machine. It arrived by fedex in 3 days. Ordering was easy and transaction went as smooth as it could. I will order again if needed.

removed top and front of machine. removed drum. replaced shaft, bearing bracket, and support bearing from inside. replaced grrounding ball and clip from outside. reassemble.
this should be available as a kit, and should include high temp grease to put in bearing bracket

You simply pry the old handle off with a flathead screwdriver, and then line up the new handle and snap it into place. It took less than 30 seconds! A breeze.

Just put the new one on! Absolutely great service!!!!
A+++++++++++++++++++++++++++++++++++++

pushed screwdriver into the two clips between the top and front to release the connection. took off front. at the bottom front left side, took out screws to access parts that needed to be replaced. put everything back together. dryer works like new. easy.

I watched the video on YouTube of the repair it was spot on. Everything went really easy and well. But the drum is still not perfectly in the middle of drum I think I will need the drum seal between drum and front door frame.

I watched the repair video on how to replace the rear bearing and ordered the parts.The video was 100% correct and showed the repair step by step I didnt even need to replay it.The repair went as expected and no left oover parts. My dryer runs smooth and quiet, My wife loves her quiet dryer.