S3600D5WW General Electric Washer - Instructions

Viewed the hot/cold valve. I saw that the cold water solinoid was burned. Ordered new valve and replace old valve. On my washer 4 screws held the switch panel, easy to remove and gave me plenty of room to veiw and do the repair.

My washer was overflowing when filling. Stopped filling when i unplugged from wall so i knew it was the pressure switch because the tube was fine. It took 28 hours from the time i placed the order to the time it hit my front porch. Got home from work and two minutes later i was washing clothes. Thanks for all the info, Tom

I unplugged the washer from the outlet. I pulled out the timer knob and used needle nose pliers to remove the clip from the rear of the knob. I removed the old knob and inspected it. Sure enough, the teeth that engage the timer were worn down to the point where they no longer would engage and turn the timer. I installed the new knob and ghen installed the new clip to secure it to the timer. I plugged the power cord in and tested the washer.....done deal!!!! Parts Select made this job easy and saved me a lot of money by not having to call a service company. The part arrived in two days, it was the exact replacement part, it was good quality. I will do business with them the next time I need to repair an appliance. Great service, great web site.

watched your video fixed it in a heartbeat I like the site very much also, I looked up the part in a minimum amount of time.I would say it took me 3 minutes total ordering and replacing Loring Gantner

I replaced the water level pressure switch but that did not fix the problem. I tried to replace the pressure tube with some rubber tubing from the hardware store but that did not fix the problem. I replaced the tubing with the correct pressure tubing for PartSelect and now it seems to be working fine. I think the old tubing had a small leak in it I could not detect and the hardware tubing was not exactly the same as the manufacturer part. Anyway it was still a lot cheaper than a new washer. Thanks for the parts and the videos, you made it a do it yourself job. John

after seeing new knob and clip, realized to pull old clip off and small piece still on stem. put clip half on new knob, put it on stem. very little room behind it. pushed clip down rest of way with very thin screwdriver. snapped in place. all done.

Couldn't get the agitator off by pulling up, then thought about it and got 2 carpenter claw hammers, inserted one on each side and puled up evenly on both and off she came. Sprayed the slots with WD Forty and popped the new on. THANKS saved us a lot of money!!!

It was only a matter of putting a new knob in place of the broken one. No tools required.

Unplug washer, turn off water and remove the supply hose, remove 5 torex screws remove panel disconnect two wire plugs remove 2 philips screws squeeze hose clamp remove old valve install new valve reversing directions

Unplugged power cord and shut off water supply. Then removed both water hoses from the dual water inlet value using adjustable pliers. Next removed four (4) star screws on top of the control panel. This required the purchase of a #20 torq screwdriver from sears costing $3. 99 Plus tax etc. Once the top panel lifted upward and to the left I was able to unplug both electricle connections on the water inlet vlaue. Next unscrewed two phillips head screws holding the water inlet value in place. Installed the new water inlet value in reverse of above. Time to complete was 22 minutes. Very easy repair to accomplish.

WATCH THE REPAIR VIDEO! I followed the easy instructions and replaced the water level pressure switch in no time. It was very easy to do!

Knob stem was split, leaving the metal bushing on the dryer's Start switch. Used pliers to remove metal collet. Aligned new knob to switch, and firmly pushed replacement part into place. Tested results and found it to be satisfactory.

Pull the Agitator out by hand no tools where needed. Took Fabric Softer dispenser off put it on new Agitator. Pushed the new Agitator on. Repair done. Sure am happy I did it myself. Service charge from repair company would have been a lot more then $50.00.

My 45 year old son did it in the shop, and it only took a short time before we were washing clothers again, and no water on the floor. The part came through the day after I ordered them. Thank you very much

Opened the package - put it on just like the old one. Didn't take 5 minutes. Good as new.