S1070A4WW General Electric Washer - Instructions

watched your video fixed it in a heartbeat I like the site very much also, I looked up the part in a minimum amount of time.I would say it took me 3 minutes total ordering and replacing Loring Gantner

KNob has gears that mesh with the washer. Simply put on the post and slid the clip into the groves on the stem. Pushed it on with needle-nosed pliers.

I pulled the top of the agitator off (the softener dispenser) then pulled the agitator itself off. I had to pull with some force. I used the socket wrench to remove the bolt on top of the agitator coupling. I then pulled off the old agitator coupling, replaced it with the new part. Used the socket wrench to tighten the new bolt. Lined up the slots on the new coupling with the agitator top, it slid on with a little resistance. The last part to replace was the softener dispencer.

Gently turned washer over onto its front. Removed bottom metal panel (3 or 4 screws on each side). Removed old belt. Installed new belt. NOTE: The new belt is a tight and perfect fit, therefore it will not want fit on to both pulleys/ rotating discs. I have found the best method is to start the belt on the disc that drives the belt. Then place as much of the belt over the disc that sits below the washing machine drum as is possible(the spinning part)and then turn the belt by hand and the belt should pop on to the disc. If the belt goes on easily you may have the wrong belt as the belt must be tight to achieve the traction necessary for the washing machine to spin. HOPE THIS HELPS!! A screwdriver may be handy in helping to pry on the belt. Good look.

replaced the dual water inlet valve

My 45 year old son did it in the shop, and it only took a short time before we were washing clothers again, and no water on the floor. The part came through the day after I ordered them. Thank you very much

I replaced the water level pressure switch but that did not fix the problem. I tried to replace the pressure tube with some rubber tubing from the hardware store but that did not fix the problem. I replaced the tubing with the correct pressure tubing for PartSelect and now it seems to be working fine. I think the old tubing had a small leak in it I could not detect and the hardware tubing was not exactly the same as the manufacturer part. Anyway it was still a lot cheaper than a new washer. Thanks for the parts and the videos, you made it a do it yourself job. John

after seeing new knob and clip, realized to pull old clip off and small piece still on stem. put clip half on new knob, put it on stem. very little room behind it. pushed clip down rest of way with very thin screwdriver. snapped in place. all done.

took agitator off, loosened bolt on coupling, took that off. Replaced new coupling and tightened bolt on top. Put agitator on and pushed down hard to set in place. I'm a 66 year old female with no mechanical ability. I ordered this part on Sat. and it was on my door step on Mon. great service and video explained how to do repair and information provided possible repair needed. Great company.....

Ordered new knob,came two days later.Really inpressed with their Service.Installed new knob within seconds.Took longer to open the plastic it was in.If you need parts,I would suggest ordering them thru PartSelect.com.

Remove agitator remove retainer screw and using Prybar lift off the old coupler ..... After removal use heat gun and wire brush to remove plastic residue from the splines of the motor shaft ... While the shaft is still warm line up the splines from the new coupler and using the mallet force the coupler on the shaft ... Install the retainer screw that comes with the coupler and snap on the agitator ... Done

Opened the package - put it on just like the old one. Didn't take 5 minutes. Good as new.

I pulled up on the fin part of the agitator exposing the gear coupling. I unbolted the nut on top with a 12 mm socket. Once the nut and washer were removed I pulled up on the gear coupling and slid it right off. Reversed procedures to install the new one.