Models > RVM1335WC001 > Instructions

RVM1335WC001 Hotpoint Microwave - Instructions

All Instructions for the RVM1335WC001
121 - 135 of 220
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Door hadle broke
Unscrew old screws at the back of the microwave door and replace the old handle for the new one.
Parts Used:
Door Handle
  • Lastenia from Bethesda, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light bulb wouldn't light.
Removed difuser (one screw), removed old bulb, screwed in new bulb, replaced difuser.
Parts Used:
Light Bulb - 40W 130V
  • Steven from Marina Del Rey, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Right hand surface lamp burned out. It apparently fald up and broke the glass cover. I wne on line when I found out the only local deaaler was some miles away and more expensive.
Simple. The parts came instantly. The glass was too big so I had it cut to size. I unscrewed the fixture with a screw driver replaced the bulb and slipped the glass cover into the frame and screwed the whole assembly in.
Parts Used:
Light Bulb - 40W 130V
  • Leon F. from Brookline, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken light lense
Removed one screw, installed new lense in lense frame, rescrewed. Done.
Parts Used:
Glass Light Lens
  • George from Marana, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bulb burned out -cracked holder lamp
pluged wires back on ,placed lamp holder and bulb back and replaced screws
Parts Used:
Light Bulb - 40W 130V Light Socket - 250V 75W
  • Terry from Justice, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door handle sheared off the microwave
The handle had been glued on previously, and broke off when I grabbed it. The glue had traveled into the holes where the plastic extends into the door for the screws to grab, so getting the screws and broken phalanges out was not easy. Using needle nosed pliers and an awl to scrape out the old glue worked, but it took some time.
Once I was able to get the screws loose and pop out the broken bits, the new part fit perfectly and is working like new.
Parts Used:
Door Handle
  • Sherry from Rutland, VT
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bulb broke in light socket
Tyring to get bulb out i ruined the light socket. Unscrewed the bottom cover of microware. Took out screw holding light socket, removed wires to socket with pliers, intsalled new socket. It was a piece of cake and the part was a perfect match.
Parts Used:
Light Socket - 250V 75W
  • Douglas from Ludington, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burned out bulb
Screwed in new bulb.
Parts Used:
Light Socket - 250V 75W
  • John from Waterford, WI
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
arcing during use of microwave
Replaced turntable coupler by removing screws from bottom of microwave and reaching through to turntable motor. The screws were a little difficult to get to because of the proximity of the microwave to our oven.
Parts Used:
Turntable Coupler
  • Gail from Amherst, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The bulbs burned out, the glass lens cracked and the light socket broke when trying to remove the bulb
Replaced the sockets, lens and bulbs. The first time the new bulb was touching the lens and the heat broke the lens and burnt out the bulb. The second time I adjusted the socket so that the bulb does not touch the lens.

Impressed by how quickly the parts arrived after the order was submitted. Two days.

Thank you.
Parts Used:
Light Bulb - 40W 130V Light Socket - 250V 75W
  • Warren from Council Bluffs, IA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light bulb burned out
took out several screws dropped down the panel under the microwave and unscrewed the bulb and put the new one in. It was a simple job.
Parts Used:
Light Bulb - 40W 130V
  • Lois Jane from Fernley, NV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
time would count down but unit would not run & heat.
remove cover, unplug secondary door switch (top switch)
remove switch from holder, install new switch, plug in wires, replace cover, very easy. door switches are a common problem
with microwave ovens.
Parts Used:
Secondary Door Switch
  • Bill from Shawnee, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Handle mount broke.
I just undid the 2 screws with Philips screwdriver and replaced handle and reinstalled same screws.
Parts Used:
Door Handle
  • Alfonso from Grosse Pointe Park, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original handle had sheared off at the face of the door.
I had to use a pair of needle nose pliers to hold the threaded plastic remnants of the original handle steady, while I used a phillips head screw driver to back each screw out. This process required careful use of the pliers as they would slip, a LOT... But once the orignal pieces were out, the new handle went in perfectly. And just in time to start cooking Thanksgiving dinner!
Parts Used:
Door Handle
  • David from League City, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Interior Light Out
Removed Cover Plate,
Removed back cover
Bulb disintegrated removed base with pliers
Screwed in new lamp
Replaced cover
Done
Parts Used:
Light Bulb - 40W 130V
  • Steven from Waldorf, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
2 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the RVM1335WC001
121 - 135 of 220
Back to Top