Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RVM1335WC001 > Instructions

RVM1335WC001 Hotpoint Microwave - Instructions

All installation instructions for RVM1335WC001 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RVM1335WC001
106-120 of 230
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken light lense

  • Customer: George from Marana, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 5 people found this instruction helpful
Removed one screw, installed new lense in lense frame, rescrewed. Done.

light lens broke a couple of years ago

  • Customer: KAREN from MANSFIELD, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 5 people found this instruction helpful
unscrewed the screw, pried up metal tabs that hold in light lens. took out broken pieces, slid in new light lens re-secured tabs with fingers, screwed in the screw again.

Lost screws for the covers on the lights over the cook-top

  • Customer: Geraldine from Clearwater, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Placed the screws in the proper areas, used the screw driver to tighten down and I was in business with light to spare. I am happy to have found the proper screws.
Thank you.

bulb burned out -cracked holder lamp

  • Customer: Terry from Justice, IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
pluged wires back on ,placed lamp holder and bulb back and replaced screws

Original handle had sheared off at the face of the door.

  • Customer: David from League City, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 3 people found this instruction helpful
I had to use a pair of needle nose pliers to hold the threaded plastic remnants of the original handle steady, while I used a phillips head screw driver to back each screw out. This process required careful use of the pliers as they would slip, a LOT... But once the orignal pieces were out, the new handle went in perfectly. And just in time to start cooking Thanksgiving dinner!

Broken lens.

  • Customer: Gary from Warren, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Used a phillips head screw driver and loosened the lens frame under the microwave. Removed the broken lens and replaced it with the lens ordered. Put the lens frame back in place and secured it with the phillips head screw.

light bulb burned out

  • Customer: Lois Jane from Fernley, NV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
took out several screws dropped down the panel under the microwave and unscrewed the bulb and put the new one in. It was a simple job.

time would count down but unit would not run & heat.

  • Customer: Bill from Shawnee, OK
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 6 people found this instruction helpful
remove cover, unplug secondary door switch (top switch)
remove switch from holder, install new switch, plug in wires, replace cover, very easy. door switches are a common problem
with microwave ovens.

Handle mount broke.

  • Customer: Alfonso from Grosse Pointe Park, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
I just undid the 2 screws with Philips screwdriver and replaced handle and reinstalled same screws.

Turntable problem.

  • Customer: Timothy from Hillsborough, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 4 people found this instruction helpful
Removed broken coulper.Snaped new coulping in placed.job done.

Light bulb was burnt out and lens was broken

  • Customer: Andrew from Bolton, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Unscrewed the lens, it hinged down, then I could remove the frame. Pulled old bulb out and replaced with new one. Replaced broken glass in frame. Reset hinge into the holes and swung it up into place. Screwed it in.

Very easy!

bulb under the microwave was burned out

  • Customer: Samar from Fairfax, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
changed the bulb

glass light lens were broken

  • Customer: Hugh from Slippery Rock, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
All one has to do is use a screw driver to remove the screws, one per lens.
Then lower the lens bracket, bend the 4 tabs holding the
lens, remove and replace the lens and screw the brackets back in place.

Less than 10 minuits.

BURNED OUT (and broken) LIGHT BULB

  • Customer: WILLIAM from BONITA SPRINGS, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
With many thanks to those who posted their experience and advice replacing the bulb, I was able to remove 5 of the 6 screws holding the underside panel and remove the socket which contained the broken off base of the bulb and extract it with needle-nose pliers. I had broken off the glass portion of the bulb trying to unscrew it due to the awkward contortion of my wrist-hand-fingers trying to grip the bulb inside the tight recess the bulb is mounted in. After concluding that I needed more information, I did a web search for 'Hotpoint RVM1435' and found helpful advice at partselect.com telling me to drop the bottom panel. Good call! Thanks everyone!

Microwave went totally dark

  • Customer: Clement from HOMOSASSA, FL
  • Difficulty: Very Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 4 people found this instruction helpful
Replaced the fuse but the new fuse blew immediately. Decided to replace whole unit.
All Instructions for the RVM1335WC001
106-120 of 230