RUD4300DQ2 Roper Dishwasher - Instructions

Remove old spring pin, spring, door
Waste of time effort and money didn't change a thing still won't dispense soap to wash dishes

Opened the door by using a star screwdriver. Pulled the door inside from the outside. Located the broken spring, put in new one (be very carefull to see how the insides are put together..makes life ALOT easier), and carefully put back together.

Disconnected power. Shut off water supply. Took off the front, disconnected copper supply line and flexible water line, removed water inlet valve. Took elbow from old inlet valve and put in on new one. Put new valve in, reconnected water lines, put back front panel. Opened water supply, Flipped breaker back on. Done and it worked!

Turned off power to dishwasher. Removed inner door panel. Cut wires as directed and installed new switches. Also installed new spring on soap door opener. Reassembled, ran and tested. Take your time, this repair is pretty simple.

easy to remove the old gasket but did not solve the problem door leaks from the bottom and water remains on bottom of machine

Opened the door removed old seal and put the new one in. The only hard part was getting the new seal out of the package. It took about 1 minute to do. Very easy.

Replaced the heating element that I ordered from Part Select. The repair cost me less than $25.00 and took me less than 5 minutes. I saved $650.00 by not buying that new dishwasher that my wife wanted to replace it with. I'm sure she will find some way to spend the money I saved(lol). Thank you Part Select.

I just followed the video, and it now works perfectly! Thanks SOOO much! great site, great info.

Shut off water supplyand removed front cover below door. Remove flexable water line (wrench set), valve and bracket (nutdriver), and input hose (pliers). Installed flexable line on valve, replaced input hose on valve, then installed valve and bracket. Found screen on input to valve almost completely blocked with buildup of materail. Replaced front cover. result, bright, clean dished.

Watched your video and replaced seal in approx. 5 minutes, probably less. Still leaked so I looked at your page for solutions, found out where the air vent was and pried it open, very disgusting mess. With screw driver and long tweezers dug out what I could then poured a mixture of bleach and water in the vent. Totally cleaned it, very white, vent cover went into a bucket of bleach and hot water and it cleaned very well. Put vent cover back on and did a load of dishes, works fine. Thank you for having such a great website, if I ever need help again I will be back. It's a shame someone didn't tell you about cleaning the air vent when you bought the dishwasher.

Removed and installed new door gasket which I found to be a simple task. Ran dishwasher and it still leaked. I then looked at other repairs submitted by your customers with the same problem. One had mentioned removing the lower spray arm and checking the screws around the pump. Sure enough, 2 screws were nearly ready to fall out and all others were loose. Tightened those, reinstalled spray arm, ran the dishwasher and no leaks. A big "Thanks" to you and also to other customers for sharing both their problem and how they were able to fix it. It sure saved me some money!!

Pulled out old gasket with needle nosed pliers, cleaned groove, installed new gasket just like the video provided on website. Took less than 10 minutes.

Got on the computer, located your site and read the repair stories.Thought, I can do this. Ordered the impeller and seal kit. I followed the same procedures as your other customers, however, when I turned it on for a test it still leaked. Went out looked for a new dishwasher, for $389.00. After talking to my wife,(been married over 60 years)decided to try one more time. Went through the same steps. Loosen the plastic ring remove The revolving spraying arm, tipped on the front to get to the bottom. mopped up the water,disconected water, electric, and hoses. Pulled the motor and pump unit, disassembled the pump unit,then I realized I had installed the rubber and plastic bearing backwards. The rubber to rubber wore out real fast. Ordered a new seal kit (no impeller) Put it all back together and it works just like it did 19 years ago. Total cost less than $60.00. It is a good feeling when your able to fix somthing like this, especially ehen your a fat 83 year old. I would like to meet the person that changed this in a half hour.

pulled out the old seal and put in the new, fixed the leak!

Watched the video and did the repair it was easy.