RT21LMXKQ09 Roper Refrigerator - Instructions

Simply done !

Spent six hours melting the ice berg, twenty minutes cleaning things up and ten minutes replacing the ice maker. The video was great the only piece of information that was missing was a statement that it may that several hours for ice to be produced. Thanks for the prompt and courteous support during ordering, a good product and support video.

I order the suspect part before pulling out the ice tray and whole ice maker for inspection. As it turns out my ice tray was peeling and all gunked up and I needed a new one. I suggest in the case of ice maker issues that you pull the entire ice maker before ordering what appears to be the troubled part. I had to replace the whole ice maker which was not really that much more money than just the part.

I replaced the motor and everything is working great!

I removed the flapper door. I removed the screw to remove the wire connection. The ice maker slides out easily. I disconneted the power wires. Removed the motor cover. Removed the 3 phillips screws. Replaced everything in reverse order. I unplugged the unit to reset the LED panels. The ice maker is still not making ice.

After my ice maker just quit working I did some troubleshooting based on the users manual. Found all the electronics to be working fine so I took out the ice maker to see if the water fill tube was frozen, it was not. Next I took off the motor access cover to discover the gear that rotates the spindle was pushed out further on it's drive shaft so it was not meshing with the motor drive gear. I pushed the white gear back on further only to discover the small locking tab on the shaft was broken off allowing the gear to slip outward and become unattached. Had to order a complete motor/gear assembly, installed in 20 minutes and all is fine again. Easy fix.

replaced whole untit very simple proceder three sheet metel screws hold unit on unplug electric conncetor and its done

After watching a YouTube video I was able to determine that my ice sensor was working properly. I was getting water through the door dispenser so I decided to pull the icemaker. First I removed the 2 hex head screws holding the ice door which gave me access to the icemaker. I removed the hex head screw holding the electrical plug cover on the bottom right side and removed it. I then pushed up on a plastic tab on the bottom left side of the ice maker and slid the icemaker out so I could access the electrical connection. After unplugging the electrical harness(plug/socket) I completely removed the icemaker from the freezer. The white square end cover easily pulled off the icemaker exposing the control and motor assembly. After removing the 3 screws holding the assembly on I pulled the assembly off the end of the icemaker. Installation was as simple as assembling the parts in reverse order making sure that the ice delivery male shaft "flat" mated with the "flat" on the motor drive female socket. After reassembly I went for a bike ride and when I returned about 3 hrs. later I was happy to see my icemaker was making ice again. This is actually easier than it sounds if you have any mechanical apptitude whatsoever.

I saw the question listed on your website with your recommended part to repair. Instead of ordering a whole new ice maker I took the chance and ordered the recommended part for repair. I saw the video and when the part came it was really easy to replace. I only wish I had found your website earlier and not gone without ice for as long as I did. Thanks.

Pulled old unit out, took control lever off and put on new unti and installed. My connections all fit so no need to change. Had ice dropping in about an hour.

I watched your youtube repairman twice. the video was very good concerning how to do the replacement.Thank you very much this is a lifesaver for people like myself that can not afford a repair person to fix broken items at the house.

My ice maker stopped producing ice after our refridgerator was accidently turned off for 4 days. Note: the on off switch in the front does turn the unit off even though the light stays on, why we need easy access to turn off the fridge is beyond me. Regardless, I spent way more time researching the problem then doing the repair. There is 2 things that could be wrong: 1 was the infra red light located on either side of the freezer, called the transmitter/reciever. 2 was the side of the ice maker control panel. Either one or if I had to replace both it would of been less then the cost of a repair man to come to my home. Prices here a good. I started with learning the diagnostic of the ice make which is learned by watching the red light flash. That informed me that it was working ok. Reference: if you hold back the hinged plate and pretend the door is shut the light should flash, flash, pause. This means its working. I went with the other route of the control module on the ice maker. This part came fast like 2 days. I watched the video on the parts web page and it was simple to do. You do have to wait until the temp goes down below 15 degrees in order for the ice maker to kick in. I won't buy another kenmore for I have had plenty of trouble with this one and its bearly 6 years old. I'm Definetly a fan of this website. Good luck DIY ers!

I looked on line to see repair instruction videos on my refrigerator ice maker. When I saw how easy I went to PartSelect and order the part (control and motor assembly). I received the part in two days with the cheapest shipping option. My 33 yr old son was visiting when the delivery was made. After we opened the box, he went to the basement for tools and the rest is history. 10 minutes work and ice a couple of hours later! No problems since.

turn off water under sink,remove water line from valve,remove line from valve to icemaker,remove 2 screws holding valve to frige,remove wire connector from valve,attach wire to new valve,cut off end of line going to valve from icemaker & push end of line into valve, attach water line to new valve,attach valve with 2 screws,turn water back on.

Pulled out the old unit removed 3 screws waited about 3-4 hours had ice. Took over night until we were actually sureby then the ice bin was full. Easy repair!