Models > RT18BMXVW10 > Instructions

RT18BMXVW10 Roper Refrigerator - Instructions

All Instructions for the RT18BMXVW10
631 - 642 of 642
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Light in the refrigerator didn't work
I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.
Parts Used:
Refrigerator Door Switch
  • Anthony from Fairport, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Freezer Ok. Refrigerator Not Cooling.
Followed recommendations from others but went with most likely by percentage = defrost timer kit. Did not solve issue. Then went with bi-metal thermostat and that did not fix the problem. Tested the thermostat as recommended on line and old part was bad, new part ok. Then I saw on line that I should have listened for fan operation. I checked and found the fan motor to be defective. Replaced the motor and refrigerator worked fine. Both the motor and bi-metal thermostat were required. Should have checked fan operation first.
Parts Used:
Bi-Metal Defrost Thermostat
  • Donald from Kissimmee, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The fan in the freezer was squealing
Took the old fan out and put the new fan in.
Parts Used:
Evaporator Fan Motor Kit
  • Maxine from Henderson, NV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice maker quit working
I found the part I needed at parts select and followed the video on their web site. They have a very informative web site, it made my job easy. I highly recommend this company.
Parts Used:
Icemaker Control Assembly
  • Donald from Banning, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice Maker stopped working. Already replaced Photo Eye
Top left mounted Icemaker facing front. Disconnect power to fridge. Using 1/4" nut driver remove single silver nut under right rear side. It holds a plastic cover over the electrical connection, unhook the cover and remove it. Release clips under front lip under both sides and entire icemaker will slip and twist out. Remove electrical connection to ice tray. Place assembly on bench and remove 3- 1/4 hex screws from under side to release bottom tray. Snap cover off motor and remove. Carefully align pin and arm on control assembly to ice tray and-re assemble. May take 30 min to dispense. Discard till clear.
Parts Used:
Icemaker Control Assembly
  • Alfred Van from Lutz, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
refrigerator and freezer would stay frozen.
I shut the unit off for about ten hours and when I turned it back on and set the temperatures for the freezer and refrigerator it has been working great.I will keep the part in case it happens again.
Parts Used:
Bi-Metal Defrost Thermostat
  • Jack from Poplarville, MS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    More than 2 hours
Was this instruction helpful to you?
Thank you for voting!
Water was running into refrig from freezer and ice cream was soft
We wasted time looking for the electrical schematic on our refrigerator (the first step in the instructions). By skipping that and reading further in the instructions, the type of cooling that the refrigerator has can easily be determined by the colors of the wires that go to the defrost timer. You need to know this to set up the timer properly for your specific refrigerator. Had I just started there, the entire repair would have taken less than 10 minutes. Very simple repair and it works like a charm, no more water coming into the refrigerator and the ice cream is rock hard. Glad we didn't have to spend lots on a new appliance. Thanks Part Select.com! BH
Parts Used:
Defrost Timer
  • William from Delano, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Installing Part for Ice Maker
Simply done !
Parts Used:
Icemaker Control Assembly
  • Larry from Weeki Wachee, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Broken water line connection
Very easy to replace. Disconnect water line. remove 2 screws pull out filler tube. replace with new one.
Parts Used:
Ice Maker Water Fill Tube Kit
  • Carl from Bloomington, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Refrigerator not cooling
Exactly how the part select video described it. Threw a little curve ball figuring out which timer setting to set it to. But the instructions provided with defrost timer walked me right through it. No problem. After installing part nothing happened for about ten minutes, which had me second guessing each and every step. Then, like magic, cold air began blowing. What a relief. Thanks so much, love this site. Refrigerator works like new!
Parts Used:
Defrost Timer
  • Bryan from Midland, NC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Stopped making ice
I order the suspect part before pulling out the ice tray and whole ice maker for inspection. As it turns out my ice tray was peeling and all gunked up and I needed a new one. I suggest in the case of ice maker issues that you pull the entire ice maker before ordering what appears to be the troubled part. I had to replace the whole ice maker which was not really that much more money than just the part.
Parts Used:
Icemaker Control Assembly
  • BOB from HOCKLEY, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Soleniod Valve Failed
The refrig. Is about 30 years old. The new solenoid looked and mounted nothing like the original. I driled holes in the frig and attach the solenoid with sheet metel screws. There were not enough fittings and hoses so I bought a braded metal hose to attach the ro line and the valve inlet. I used the parts in the kit to attach the water feed line. To the ice maker I did not try to stuff all the hoses and lines back into the cramped cavity in the frig. W ell how does it look? The solenoid sticks out a little and there are a lot of hoses behind the frig. I do not spend much time behind the frig so who cares. The ice maker is making ice!
Parts Used:
Single Outlet Water Valve Kit
  • BOB from LAKE HAVASU CITY, AZ
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the RT18BMXVW10
631 - 642 of 642