RS20AQXFW00 Roper Refrigerator - Instructions

1. pull refrigerator from wall. 2. unplugged refrigerator. 3. removed cardboard backing from refrigerator. 4. removed (2) mounting screws 5. marked and removed leads from leaky valve. 6. removed water and ice tubing from valve. 7. install in reverse order

I unplugged the refrigerator then I took the bottom screw out of the ice maker. I loosen the other two screws and picked up on the ice maker and it came out. I saw that the top of the ice maker where the screws are they sit in a groove so you dont have to take the top screws out just loosen them and pick up on the ice maker and it will come out. Then I unplugged it from the old ice maker not from the wall of the refrigerator. The reason is I didnt want to mess up the cover that hides the plug in the wall of the refrigerator. Then I took the metal on and off bar off the old ice maker and put it on the new one. Then I took the face off the new ice maker and unplugged the new wire. All you have to do is press down on the little clip and pull back on the plug. Then I plugged the old plug into the new ice maker. Then I set the ice maker in the grooves on the top screws then iput the bottom screw back in then I tighten all screws. I plugged the refrigerator in. I started getting ice in thirty minutes. My wife think I can fix anything now. Thanks

After watching the convenient movie, the replacment of the Thermostat was very simple and easy. i woul strongly advise you to take a picture of the wires before disconecting so, you will be sure to to reconetc it again.The replacment was a success and the refrigerator has been working since them

Took the broken drawer out and installed the new drawer.

Parts Select Website was very easy to use, selected the correct part for me with no problem. Same drawer as Sears was selling but for much less money. Drawer came in new from the factory. Great Service, Fast Delivery. The shipper had damaged the drawer--something poked through the box and put a whole in the drawer--a small one cause by a sharp instrument of some kind. Called parts select, the problem was very simply rectified by refunding my money and then I bought a new drawer at the same time. No fuss, no muss. Fast delivery and great service.

My wife removed the broken Grille and replaced it with new Grille without using any tools. She was aware of how to remove and replace the grille as she has done it over the years when cleaning under the refrigerator.

Removed the auger apparatus from the ice bin, replaced the auger drum and then reattached the auger apparatus to the bin. Cause of breakage was due to ice melting in the bin and then refreezing. Keeping the many parts in the correct order on the auger can be difficult.

Pretty simple, remove the old one and put in the new one - kinda alike the "Automotive Tech's" of today.

Instead of trouble shooting what part was bad, just replaced the whole unit. Probably cheaper in the long run and the whole process took less than 15 minutes. Pulled the old icemaker out, plugged in the new one and back in business.

The video of the repair that was on your website was extremely helpful. It showed in detail how to replace the parts item by item. I could not have done it correctly without the video. I believe anyone could have replaced these parts with your instruction video.

Watched video on changing out the ice maker motor and followed instructions and it was as easy as video demonstrated. Received replacement motor in 3 days. Great service.

Nothing to it, just slide the drawer in. Fast Delivery, Smooth Transaction, Great Service. I will use them for all the parts I need in the future. Thanks

removed ice make from freezer. Removed end cap and replaced control and mostor assembly. The associated You Tube video was very helpful.

Took the old one out and put the new one in. No problem.

remoove all the food and shelves out from the freezer section, remoove the light bulb lens ( 1 phillips screw) remoove light bulb, take out 6 srews on the back panel then slide out through the top with a slight bending curve motion, the bimetal thermostat will be clamped to the evaporator inlet, ( just after the cap tube) snap it off, then cut the wires about 2 inches from the stat, strip the ends about a quarter inch with wire strippers, same on the new stat, then use 16 or 18 gauge butt splices and crimp them , then reassemble in reverse order.