RM255PXP0 Whirlpool Microwave Oven Combo - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
burned out element
Open door, remove two screws, pull plug, pull element; reverse process..done.
Parts Used:
-
Matthew from Tolland, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Was not able to take out the screws
I hired a handyman who had to take out the back cover of the stove and spray the screws with a rust remover both inside and out. It was a tough job, but with an electric screw driver (not sure if that's what it's called), the two screws came loose after over two hours of work. Make sure you clean the oven screws!
Parts Used:
-
Deborah from East Falmouth, MA
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Element burned out
Removed two easy to reach screws that attach metal securing plate and element to rear of the oven with screw driver, pulled wire connectors from old element, attached wire connectors to new element, reattached the metal plate and element to the back of the oven with the two screws. Finished!
Parts Used:
-
Shaun from Eustis, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
burner element melted and almost caused fire
very easy repair took less than 5 minutes removed racks from oven and used a number 2 phillips head screwdriver to remove the 2 screws pulled element out detached the 2 wires and removed element reattached wires to new element pushed element back in and reinstalled the screws.done note* i found this to be a good time to clean the oven so the night before part was to arrive i sprayed a good coat of oven cleaner on the 3 sides and lower part of oven after removing element it made it very easy to clean the oven up.
Parts Used:
-
keith from plain, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
range installer broke a screw off & busted the plastic piece
-
Christina from West Des Moines, IA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
bake element started sparking and flashing off while wife was baking cookies
took the two phillip head screws out then gently pulled element forward to expose wire connection. then used needle nose pliers to disconnect wires. removed old element and replaced.simple task. took 5 min
Parts Used:
-
michael from roaring spring, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Bottom element burn't out
My new part was a exact fit, 20min replacement time, works great.
Parts Used:
-
Doyle from Gilbert, SC
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
lower heating coil not working
-
Christopher from Mill Spring, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broiler element went out in my oven
-
Donna from Dacoma, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!