Models > RK777G*D2 > Instructions

RK777G*D2 Hotpoint Wall Oven - Instructions

All Instructions for the RK777G*D2
286 - 300 of 327
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
burner/element was burnt & split
my husband did the repair-said it wasn't "too bad". I had ordered the part at 9:00 PM on Wednesday. It arrived Friday AM. Instead of calling in a repair person, we spent $18.23 and the oven works fine !!!!
Parts Used:
Bake Element - 240V
  • Beth from Fairfield, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
Solenoid failed due to excessive heat.
Removed back panel. Removed the defective solenoid on its bracket. Replaced it with the new door latch solenoid. This was relatively easy. Replaced the back panel. Tested self cleaning feature. Everything worked fine. I have preformed this same repair once before.
Parts Used:
Door Latch Solenoid
  • Joseph from Martins Creek, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
bake element failed
I unscrewed the element mounting plate, Unscrewed the electrical connects. Used tyhe new screws furnished with the replacement element to attach he electrical connectors. Replaced the two screws that attach the element.
Parts Used:
Bake Element - 240V
  • Joseph from Califon, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Bake element burned out.
Removed the old bolts and removed the element with a socket wrench. Reinstalled fairly easily. The only problem was the manufacturer made the wires very short which made them hard to grab and connect to the element. Need a locking pliers or something similar to hold the wires during reconnection.
Parts Used:
Bake Element - 240V
  • andrew from Milwaukee, WI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Heating element not heating the oven.
I removed the two screws holding the lower heating element from the back of the oven. Pulled it out so I could see the wire connections, and separated the wires from the element. Took the new heating element from Parts Select and reversed the procedure. Checked all the connections, and turned on the oven. The new heating element worked like a charm. We're back in business. Very easy job.
Parts Used:
Bake Element - 240V
  • William from Aledo, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Uneven cooking
Saw a You Tube video on how to replace the Bake Element. Looked fairly easy. Ordered part on a Friday afternoon - it showed up on Saturday! Turned off power, cleaned out junk at bottom of oven, removed 2 screws with nut driver, unscrewed both wires, making sure they didn't retract back behind the insulation. Put new one in place, connected 2 wires, screwed unit back in, turned on power. I think I spent more time running up and down the stairs to turn off/on the power! Cleaned the oven for 2 hours, and now it is like brand new! I will probably do the lower oven next.
Parts Used:
Bake Element - 240V
  • Brian from Libertyville, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Element burnt out
Took out the old put in the new....
Parts Used:
Bake Element - 240V
  • Debra from St Pete Beach, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Oven element had burned out
Turned off power. Removed plate in rear of oven and then unscrewed the 2 connectors and then put on new element in reverse order. PartSelect was very helpful in id of part and needed repairs. Very prompt delivery and excellent business accumen offered. Customer service rates a 10 of 10!!
Parts Used:
Bake Element - 240V
  • Ed from Ponte Vedra Beach, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Oven not heating properly
After removing the element the wires were so far back and were difficult to reattach because they were so short. Instead of putting the screw through the wire into the the element i put a screw threw the bottom of the hole in the element with a nut to hold it in place and then installed the wire on the screw that came through with a nut to hold the wire. The next time i replace the element i will tie a string around each wire before i remove the screws so they will be easier to attach.
Parts Used:
Bake Element - 240V
  • Ernest from Woodside, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Bake Element fried
turned breaker off, checked to make sure no power to oven. Removed screws at bracket from old bake element. removed screws from wires attaching to bake element. Removed old bake element. Put wires onto new element, put screws in new bracket. Turned breaker back on, turned on oven, works great.
Parts Used:
Bake Element - 240V
  • ARTHUR from PASO ROBLES, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Heating element was burned out.
removed and replaced the heating element
Parts Used:
Bake Element - 240V
  • JAMES from EUSTACE, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Replacement of bake element in wall oven
I looked up the part on-line and read previous repair comments on the ease of replacement. I turned off the electric power breaker - selecting the one labeled "50" as suggested by a previous purchaser. The oven light went off immediately. I then made sure I could remove the burned out element before I ordered the replacement. This was a little difficult, as the octagon shaped screw were rusted after 26 years and difficult to remove. I sprayed with WD-40 and followed the directions given by previous repairers. I was quite proud that when the part came a few days later, I was able to install without too much difficulty. Would have been easier if my arms had been longer. This oven located next to wall - set up a little on the high side for this 72 year old 5'2" woman. Good job!!
Parts Used:
Bake Element - 240V
  • ELEANOR from MOBILE, AL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Noisy fan
Emptied freezes, turned off power, took floor of freezer out [4 screws ], took two screws out of fan mounts and replaces fan. Reassembled by reverse process. Simple
Parts Used:
Evaporator Fan Blade Kit
  • Robert L. from Eldred, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broiler Element burned out
From inside the oven after turning off the breaker I removed all of the mounting screws with a nutdriver, I removed the wire screws after taping all of the wires together with a small piece of tape to prevent them from falling back into the opening. I installed the wires with the original screws as the provided screws would not fit the holes, tightened them, removed the tape and placed the element back into the opening. I then tightened the hanging brackets, after getting them to align and then tightened the rear mounting bracket. It did help to adjust the baking rack down and leave the baking rack in place to have a place to rest my arms. The install then became a piece of cake!
Parts Used:
Broil Element
  • Chuck from Ellettsville, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Hearing element burned through
So easy! I just unscrewed the old one and just popped the new one in. So great!
Parts Used:
Bake Element - 240V
  • Charles from Spring, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the RK777G*D2
286 - 300 of 327