Models > RK777G*D2 > Instructions

RK777G*D2 Hotpoint Wall Oven - Instructions

All Instructions for the RK777G*D2
301 - 315 of 327
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Eye burnt through
Turned breaker off, unscrewed the element plate from the back wall, then unscrewed the power wire then put the wires on the new element the screwed the element and plate back into the back wall, then turned the breaker back on then turned it on to check and it actually works better than other one. Heats evenly now.
Parts Used:
Bake Element - 240V
  • Chad from Greer, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Oven element burned out
It was easy just a screw driver and ordering the part was made simple with pictures of the different elements. I could not belive you had the part.Thank you
Parts Used:
Bake Element - 240V
  • Albert from Hazlet, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Bake element burned out
Make sure the oven is off , remove 2 mounting screws , remove 2 screws wire to element , repeat previous steps installing new element
Parts Used:
Bake Element - 240V
  • thomas from bluefield, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
No problem
By using a sscrewdriver with a socket,the job was easy
Parts Used:
Bake Element - 240V Broil Element
  • jeff from South setauket, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
The bottom heating element in my oven cracked.
I turned off power to the oven and used a nut driver to unfasten the heating element from the back of the oven. I pulled it a little bit out, then used a screwdriver to disconnect the wires from the terminals. I used the new screws provided with the new element to connect it to the wires, then screwed it back to the back of the oven. I turned the power back on and tested it. It was easy. No need to replace the oven yet.
Parts Used:
Bake Element - 240V
  • Scott from Northborough, MA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
element burned out
removed and screwed new one in
Parts Used:
Bake Element - 240V
  • anthony from watervliet, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
Oven door gasket hard, noot sealing
I thought it would be a simple matter of removing the inside glass (4 screws) and replacing the gasket, but it turns out that on this model I had to start on the outside, remove the drawer, then remove the front door cover, then undo a screw which held the inside two-tier glass in place, THEN I could remove the four screws and the interior panel which holds the gasket in place. THIS IS A TWO PERSON JOB unless you choose to use masking tape to hold the exterior door cover in place while removing/replacing the many screws which hold it on. WHILE REPLACING THE INTERIOR COVER WHICH HOLDS THE GASKET IN PLACE, YOU MUST PERIODICALLY STRETCH IT HERE AND THERE TO GET THE "SNAKE" TO EXTEND THE ENTIRE WAY AND TO SEAL TIGHTLY.
Parts Used:
Oven Door Gasket
  • STEVEN from HERNDON, VA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Broken bake element
Ordered part. Part arrived within 3 days. Went to my nextdoor neighbor and sniveled about "being afraid of electricity." He came over, unscrewed 2 screws, pulled out old element, replaced with new element, gave me a look that said, "must be nice pretending to be a helpless old lady and getting your way all the time." Smiled and went back home. Sure love my neighbor(s)!
Parts Used:
Bake Element - 240V
  • Marx Titus, from Danville, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Bottom element had burned through.
Quarter inch socket was all that was required. The plate that covers the slot where the element threads through from the rear was smaller than what was on the original element, and it took a few attempts before it was secured properly to cover the opening, but other than that, it was a snap. I estimate that I saved well over $200.
Parts Used:
Bake Element - 240V
  • David from Atlanta, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
broil element failure
Unscrew 4 easy nuts and 1 most difficult nut, gently pull both long and short wires, at this point assure the wife that you did turn off the power.You may wish to attach a cord to short wire as it wants to vanish into the rear bowels of the oven On instruction of the wife clean the oven. Reverse dismantling procedure. Switch oven on. Bask in wives praise.
Parts Used:
Broil Element
  • Glenn from Plano, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
exchanging broiler element
Even though my sons offered to do the repair, I opted to hire an appliance technician to do it and it took him at least 45 mins. with his experience and tools. apparently the inside wall wires were shorter and more difficult to access and grip and I'm glad I did. It should last another 20 years and I'll be dead!
Parts Used:
Broil Element
  • Beverlee from Mill Valley, CA
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    30 - 60 mins
Was this instruction helpful to you?
Thank you for voting!
Lower baking element was not working
You must turn off the power to the oven since it's directly wired into the electric. One person holds the flashlight while the other removes two nuts, then two screws. Tight space to work in with head in oven. Tricky getting the screws back in and them making sure the unit is centered in the space when tightening the screws. Turn power back on when done. Works like a charm.
Parts Used:
Bake Element - 240V
  • Marie from Princeton Junction, NJ
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
I replaced the lower heating element of the oven.
After removing the two oven racks, sitting on a low stool positioned on the side of the oven door, and placing a magnetic light on the oven wall, it was easy and comfortable to change out the heating element. A magnetic screw driver is helpful. Two screws had to be removed to free the element from the rear wall of the oven. Then two small screws needed to be unscrewed to free the terminals from the oven-wire terminals. The reverse procedure was followed to install the replacement heating element.
Parts Used:
Bake Element - 240V
  • Allen from Naperville, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broil Element burned out
Removed old element, checked continuity and element was bad, Fit new element and everything was good. No problem except my arms were not long enough!! Repairs took about 15 minutes.
Parts Used:
Broil Element
  • Myer from Cleveland, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Element burned out
Turned off circuit breaker (220) removed old element - replaced with new element.Very Easy - inexpensive and arrived fast.ordering was easy by using serial number.
Parts Used:
Bake Element - 240V
  • Anthony from Tully, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the RK777G*D2
301 - 315 of 327