Models > RK777G*D2 > Instructions

RK777G*D2 Hotpoint Wall Oven - Instructions

All Instructions for the RK777G*D2
16 - 30 of 327
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broiler Element quit working
First I removed the two screws in the back. then I removed the two screws attached to the brace at the top. pulled the old element out. Removed the screws that attatced the wires to the element. Attached the wires to the new element. Pushed the wires back in. Pushed the element in and attached the screws. Reattached the support. Turned on the broiler. The element smoked for a few seconds before getting red hot. It is working fine.
Parts Used:
Broil Element
  • Parker from Blanchester, OH
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
9 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broiler element not working
Pull the stove out from the wall and unplug. Had to remove back of stove, the aluminum sheilding and the duct work to get at wires use nut driver. Then used nut driver to remove nuts from broiler unit inside stove. Take the front overn dover off first. The new part did not match up with the wires so I used a needle nose to spread the wire clips just a tad so they would fit over the tabs of the broiler unit. Do all of this behind the stove as you do not have eough wire to do this effectively from the oven side. After I had the tabs fitted to the broiler unit. I removed them and fed wires back through the stove. I then went back to the front of the stove and put the broiler back in and put support bar back in to ceiling of stove and the two nuts back on to affix broiler to back of oven. Put the aluminum baccking and duct work back onto the back of the stove and plugged it back in. Pretty easy job.
Parts Used:
Broil Element
  • Shawn from Newburg, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
9 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broiler Element failure
Turned off power at panellboard. Disconnected mounting hardware from inside oven chamber. Pulled failed heating element with wires attached into the oven chamber. Disconnected wiring and reconnected them to the new heating element. Tightened screws while holding connectors with pliers. Applied electrical tape to connections. Pushed wires back into opening and secured heating element back into place. Restored power nad verifed proper operation. The other heater purchased will be used when the bake element finally fails,
Parts Used:
Broil Element
  • Todd from Pineville, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
8 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broiler element finally burnt out after many years of cooking.
(1) Turned off power source.
(2) Removed rust on screw heads before attempting to loosening them up.
(3) Pulled the element out to expose the connections.
(4) Disconnected with phillips screw driver, taped off wires to prevent mixed-up during re-installation.
(5) Re-installed new element using new screws provided.
Parts Used:
Broil Element
  • Gerry from Union City, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
9 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven heating element would not heat
First, and most importantly, flipped the circuit breaker and turned off the power to the oven. Next, Unscrewed the old element and disconnected the wiring. Then, removed the old element and replaced it with the new one.
Reconnected the wiring to the new bake element and screwed it back onto the oven.

Voila! Turned the oven on and watched the new element heat to a bright red. We had an oven once again, and saved ourselves more than $100. Yay!
Parts Used:
Bake Element - 240V
  • Margaret from Stone Mountain, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
9 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven bake element melted
Removed the racks, removed two screws holding the element to the back of the oven, removed two screws holding wires to the element, installed by the reverse. BUT in my case the new element still didn't heat. The part was perfect so when the old element melted and shorted, it must have damaged the controlling switch (220V requires dual pole switch--apparently one side is now bad). Since the oven is over 30 yrs old, I'm returning the element and will buy a new oven.
Parts Used:
Bake Element - 240V
  • John from Olympia, WA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
7 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Interior light needed replaced
Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.
Parts Used:
Light Bulb - 40W
  • Leo from TWIN FALLS, ID
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
9 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken fan blade in the freezer compartment
Unplugged frige, removed top shelf, pulled broken fan blade off. Replaced with fan blade just purchased from PartSelect. Very simple repair. Orderd and recieved the right part.
Parts Used:
Evaporator Fan Blade Kit
  • John from Cumberland, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
7 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Twice I ordered the oven light bulb & each time the light bulb was defected
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
Parts Used:
Light Bulb - 40W
  • Barbara from BELLEVUE, WA
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    Less than 15 mins
8 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old element burned out
Turned off the power to the oven. Removed the racks. Removed two screws holding the unit to the back of the oven. Removed two screws holding the wires to the terminals. Removed the old unit. Reversed the process. Piece of cake. The only "difficulty" was that the old wire-to-terminal screws required a nut driver (as did the unit-mounting screws) while the new wire-mounting screws required a #2 Phillips screw driver. Took me a couple of minutes to get one of those from the garage.
Parts Used:
Bake Element - 240V
  • J T from Clarksville, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
7 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bake elelment was out
I turned off the breaker to the oven. Removed the old element and replaced. Turned on the oven breaker and turned the over to 350 and it was working great. I was very proud of myself as a 68 year old widow.
Parts Used:
Bake Element - 240V
  • Jackie from Hillsboro, OR
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
27 year old elements finally went out.
First I cut the power then I pulled the mounting screws, pulled hte elements out enough to get the screws out and then did it in reverse. Piece of cake.
Parts Used:
Bake Element - 240V Broil Element
  • Christopher from Plant City, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Wrench set
6 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Bake Element in the oven had "blown out" on the right side, and wouldn't heat.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Then I connected the two wires to the new element with the screws provided and simply replaced the screws that hold the element in place.
In 20 minutes the job was done. It was a snap to make the repair!
Parts Used:
Bake Element - 240V
  • Keith from Lima, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
5 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I broke the glass door while installing built in oven
I was so relieved to find the replacement glass for the door on my built in microwave/oven. I was worried about shipping this tempered glass panel but it was recieved well packaged. As soon as I openned the packing, I removed 6 scews holding the trim around the oven door, slide in the new glass, reinstalled the scews and grabbed the glass cleaner. I was finished. Part select is a tremendous resource.
Parts Used:
Outer Oven Door Glass
  • David from Morrison, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
5 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
baking element burned out
Removed the nuts securing the element to the back of the oven, pulled out the wiring and unscrewed the wires. Went on line and found the part, ordered it, received really quickly and put the part back in the oven. Works great. Oh, I also turned off the power.
Parts Used:
Bake Element - 240V
  • Terrance from Fresno, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Socket set
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the RK777G*D2
16 - 30 of 327