RGB745WEH7WW Hotpoint Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replace medium burner for gas cooktop
Very easy to remove grates, burner cover and remove old burner head. Very simple process, but surprised that there was no efficient way to clean carbon deposits from my old burner. Burner video instructions on line insured I installed the new burner head correctly (actually, pretty hard to get wrong), and burner worked correctly immediately. Will likely replace other burners in time as the new one is so "silvery" colored compared to my other burners.
Parts Used:
-
Charles from Houston, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Flashing F7-31. Could not set anything on stove
Removed 4 nut type screws. Removed 4 philip head screws. Removed unit from stove & matched up about 5 wires that are well marked from old to new
Parts Used:
-
Robert from Hamburg, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Threads on elbow stripped out
Part was purchased to replace damaged elbow. During the conversion to LP gas the elbow threads were stripped from over tightening the collar nut. To accomplish the replacement: 1. remove 2 sheet metal screws holding protective shroud in place. 2. disassemble the compression fitting CAUTION DO NOT OVERTIGHTEN 3. loosen elbow collar nut if necessary and remove elbow. 4. reassemble starting with the compression fitting. 5. connect the elbow to the broiler burner with the collar nut 6. tighten all the way down turning nut cw for LP conversion CAUTION DO NOT OVER TIGHTEN 7. with broiler on adjust flame and check for leaks
Parts Used:
-
Ronald from Millington, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Wrench set
Was this instruction helpful to you?
Thank you for voting!
oven ignitor was bad
the instuctions that came with the part made the installation easy. it was a big help because i had never done it before
Parts Used:
-
Donald from Rio Vista, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Burner would not ignite.
Could not have been simpler. Burner head dropped into place and was held in place by gravity. Not possible for part to go in incorrectly.
Parts Used:
-
John from Los Angeles, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Oven wouldn't lite.
Went fast. So easy a kid could do it. Shipping was unbelievable. Seemed like I ordered it one day and it was there the next.
Parts Used:
-
Michael from Granbury, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Oven liner melted....needed to replace bottom
Removed the old oven bottom by removing two nuts. Be careful...don't drop the nuts! Removed the heat shield that was attached with four nuts to the old bottom and transferred it to the new oven bottom. Then placed the new bottom in the oven and secured it with the two original nuts. Easy...but don't forget about transferring the heat shield and don't lose the nuts.
Parts Used:
-
Ruth from Somerset, NJ
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
failed ignitor
First, I need to say what a phenomenal shipping response from parts select. You could be forgiven for thinking I asked them to overnight the part - Removed the panels needed to give me access and swapped out the part. Most difficult was attaching the new wire. Only about 2" of the old wire protruded and it was quite tricky to get a wire nut back on.
Parts Used:
-
Wayne from Carbondale, KS
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Gas oven failed to heat.
I opened the oven to observe the ignition process. When I put it on "broil" I saw this silver tube begin to glow red and then the gas turned on and the broiler ignited. When I tried it on "bake", nothing happened. So I assumed the igniter on the bottom element was defective. As usual, I came to PartSelect and searched for the part which I immediately found. Then I found comments other users had left which indicated the igniter was what caused the same problem on their ranges and that it was easy to replace. The part came in 3 days with standard shipping and I installed it in about 20 minutes. Now the range works like new for about $70 instead of the $200 a repair person would have charged.
Parts Used:
-
Thomas from Cedar Park, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
turn on the oven and after a minute or so there would be a mini explosion and the oven would heat normally
went to parts select and entered my oven model number and read the typical problems and remedies.....selected the one that fit my problem and order the igniter and it arrived in less than 2 days. took about 20 minutes to install using the instructions and this cured the problem. saved a $100 service call charge.
Parts Used:
-
Leo from Temple, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Oven would not work - igniter would not heat up
I removed the racks, door and bottom of the oven (2 screws). The wires went lower so I pulled out the bottom drawer. I removed two wire nuts and removed 2 screws to remove the burner tube and igniter assembly. I removed two screws to remove the igniter from the burner tube. Replaced the igniter (2 screws), replaced the burner tube/igniter assembly (2 screws). Connected the wires - which one goes to which wire doesn't matter - screwed on the wire nuts and turned it on. It worked so I put it all back together and cooked a turkey.
Parts Used:
-
David from Ypsilanti, MI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The new ignighter did not come with the connectors to simply replace the part. I had to cut the old ends and splice them onto the new part.
I removed the broiler and the cover in the oven itself. I then removed the burner assembly, and unplugged the two wires of the ignighter. I then removed the ignighter from the Burner tube. I then spiced the old wire ends onto the wires of the new ignighter. I then replaced the Burner assembly, hood up the wiring and reassembled the oven and broiler.
Parts Used:
-
Terry from Jameson, MO
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
gas leak
-
robert from deerfield beach, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Wrench set
Was this instruction helpful to you?
Thank you for voting!
failing oven igniter
I'd rather disrobe how well your Co does business Repair info.A, Sales Rep. A, Parts, A. speed of delivery ,A+
Parts Used:
-
James from New Hope, PA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Electric range had parts missing and discolored end caps (house was a lease to own)
The range was in very good condition but the end caps had yellowed from hot temperatures. The missing broiler pan and one oven rack were an easy fix as was the end caps. I had a problem in getting the correct parts (end caps) because I did not order correctly. It was totally my fault. The customer service person was wonderful to work with. He helped me order the correct part and sent the return label and instructions that made it easy to return the un-needed parts.
Parts Used:
-
Nancy from Fuquay Varina, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!