REL3636AW0 Roper Dryer - Instructions

i took off the back of the drier and with a screw driver removed the 2 screws and put the new part on

I noticed my dryer was heating, but not tumbling. I"m a 53 year old single female, and my dryer I bought used 3 years ago. I had no clue what the problem was. I texted my brother and said, "it heats but doesn't tumble - is it shot?" He texted back "probably the drive belt - pop the top and see." So I popped the top, and sure enough, the belt was broken. So I googled "diy + dryer + drive belt" and watched a You Tube video. I then drove all over town looking for a belt, and the only place that carried it had closed at noon (saturday). So I googled " appliance parts + dryer and came to this site, ordered the part and it was delivered in two days.
I borrowed a nut driver from my brother, removed the front of the dryer, used a plastic cup to prop up the drum. I put the belt on the drum, being sure to place the ribbed side down, looped through the pulley and onto the motor, removed the cup, put the front back on, dropped the top, replaced the lint trap and the two screws holding that in place, turned the dryer on and voila! All done.

Took a bit to first figure out how to get the front of the dryer off in order to access the motor, wheels, and belt, but found a "how-to" online. Once I had that, the rest was easy.

Lubricated motor and guide wheels but squealing still there. Then noticed the "idler pulley assembly" (the part that keeps the belt tight against the drum) looked a bit old and worn. Ordered a replacement part on this site because it was much much cheaper than a service call, installed it.... and NO SQUEAL!!!

remove the front panel, belt [notice the way the belt is fasten] remove the tub, support bracket to the drum roller, and slide the new drum roller on and place the tre ring in the slot. then re-install everything in reverse

Found the switch part on the floor and after I figured out where it came from it was minutes before it took to find the web site and order the part, I then watched the installation video which helped with a few pointers and days later it was installed and fixed for 10 dollars with shipping,AMAZING!!!

Took back cover off. Cleaned out the lint that had built up inside the dryer. Replaced the lint trap housing and lint chute seals. Also replaced the drying vent hose. Works great now.

Replaced the Thermal Fuse first - 30% chance - didn't help! Then I replaced the resistor - Not an in-kind replacement - looks different-Guessed the wrong place first [no specific directions :( ] and got some sparks - Yikes! Picked the second place and installed the resistor and it work PERFECT. Spent Less than $50 and back in business = GREAT!!

The repair was really easy and I loved the DIY videos they were great, not many tools needed to do these repairs that was great. The only thing is this didn't solve my issue.

Numbet one - unplugged the dryer. Then disassembled dryer (front panel, loosened vent from top panel and removed drum). Removed motor after carefully documenting wires and their corresponding numbers, along with pictures. Read directions several times to assure we understood process. Followed instructions for replacing connectors. Used pliers and screwdriver to install motor clips. This took numerous, patient attempts. We also had to partially remove the vent in order to reinstall the motor. Then replaced drum, front cover, reattached vent to top cover. Reattached outside vent hose. Plugged dryer in and tested it. Motor replacement worked fine and fixed the problem (squealing).

Used the YouTube video sent by this site

Take out 2 philips screws in lint trap holder on top. Use flat screwdriver to pry up front left and right of dryer top near outside edges and tilt up out of the way. Remove 2 push-on AC connectors on door switch and remove plastic clip holding wires to dryer's front top metal edge. Remove (2) 5/16" sheet metal screw on inside top left and right edges to free up front panel. Lift front panel about an inch and it'll then pull off. It helps to have a second person to help hold or remove the drum at this point. It took 3 times for me to guess right on the squeak. First time I replaced the belt, second time I replaced these rollers, third and final time I replaced the idler pulley, the shaft of which had worn completely off so clearly i can't figure out how we didn't see (or hear) it the first two times! Dri-Slide lube helped stop the squeaking the first two times, but it always returned until this time, now I have a thoroughly rebuilt dryer for the next generation! (PS vacuum out the bottom of the dryer while it's open to remove both lint and greasy roller shavings - do this FIRST and you'll have cleaner hands & clothes!)

I did what any novice would have done. I took the entire thing apart to get to the gas jet. I did not know about the thermal fuse until I got to the schematic behind the timer and controls. I was a tech back in the 70's and 80's and only worked on electric dryers. Back then I would remove the heater core and twist the coils together to save money. So I had no idea how a gas dryer heating unit worked. So now any one that reads this. You do not have to take the dryer completely apart, I did that for all of you. Just replace the thermal fuse on the back of the unit by unplugging that wires and removing the screws! It looks like a long white piece of plastic with 2 wires to it. You will find this under the full metal shield on the back of the unit. This should be about a 1 hour repair at the most!

Removed rear panel, removed 3 screws and old element and installed new element. To install new element I only needed one screw and spliced in the two wires that were provided with the element. This repair was simple and now the dryer works great.

After un-plugging the frig and allowing it to defrost, we emptied the frig and gave it a thorough cleaning inside and outside. I then removed the shelving in the freezer and the face plate at the back of the machine. One of the defrost heater coils had burned out and there was a loss of continuity which was keeping the frig from defrosting properly. The old heater snapped out easily. I went to this website and ordered a new defrost heater assembly which arrived practically overnight. It was identical to the old one and installed as quickly and easily as the original had come out. I put the faceplate back on, put the shelving back in, placed a thermometer inside the fresh food section, plugged it in and waited until I heard ice cubes drop. The fresh food section was holding at 41 degrees F which is optimum. The refrigerator has been working smoothly every since! Easy job!

I removed the back panel and tested the Thermal Fuse, the Thermostat and the Heating Element with a meter. The Thermal Fuse gave a bad reading. I proceeded to clean the dryer and lint pipe of all lent. I installed the new Thermal Fuse and put the back panel back on the dryer. The dryer worked for two loads of clothes and the Thermal Fuse blow again. I'm now at the end of my rope. I don't know what else to check and I can't continue to buy parts for only two loads. I guess I will have to invest in a new dryer.