Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Top glass top burner wasn’t working
I first ordered the wrong part and had to call customer service. They handled the return and ordered the new piece beautifully!! The installation was really simple. Once I took out two screws holding the top down, I removed three clips holding the burner on then switched out the electrical leads. Put everything back and it worked perfectly!!
Lots of jiggling until I found the screws to remove. After finally getting the top off the base there was the Instructions on a pamphlet taped to the bottom. The key tho get the top off is to remove the face and remove the proper screws( they are identifiable)unplug the electric plug 2 screws on the back sides and poof it is free!
I knew I had a bad control board. Using the repair videos, replacing this part was very easy to do. While I was at it, I replaced my oven temperature sensor. as well, and even though it wasn't bad, I replaced my oven heating element so that I could get some more mileage out of my 14-year-old range. The issue: after completing my repair actions, my oven element still would not heat. I double-checked my connections and I discovered I hadn't ensured one of the wires on the control board was properly seated. This was one of the wires that go to the heating element. After ensuring proper connection, everything worked perfectly!
I turned off the circuit breaker and unplugged the stove. I removed the back panel and marked the location of the wires on the new oven clock control. I detached the wires and removed the old card. I installed the new one and reconnected the wires. I plugged the stove and turned on the circuit breaker. All the lights came on and the oven worked fine. I reinstalled the back panel and it took me less than thirty minutes to complete the job.
1. Unplug the range power cord from the outlet. 2. Moved range away from the wall and countertop. 3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock. 4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel. 5. Using a nut driver remove 4 screws that secure the main control board in place. 6. Take photo of the wiring on the main control board if not color coded. 7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board. 8. Remove wires with needle nose pliers. 9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board. 10.With a putty knife carefully pry the face plate from the old control board. 11. Install the control board face plate onto the new control board. 12. Install the color coded wiring in place on the back side of the control board. 13. Replace the control board into the range, and install screws, and rear panel of the range. 14. Plug cord into outlet and test range for proper operation.
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
Remove drawer by pulling out and lifting up so drawer will slide out of range. Use 1/4 inch Nutdriver or socket - remove the screw that holds the drawer support to the body of the range. Remove support and install new one with screw Pay attention to the way the support fits. There are two holes one for the screw and the other for the plastic prong on the bottom of the support. The prong fits in the bottom hole and the screw in the above hole.
My electronic control board went out so I could not use my oven. My oven light blew as well.
I started with changing the bulb. I removed the small bracket that holds the glass cover over the bulb unscrewed the bulb and reversed to replace the bulb. To replace the control board I removed the top plate on the back of my stove took the small screw's out of the control panel and unplugged the wire's. Plugged the wire's into the right spots on the new control board and put it back together.
Oven no longer working after running the self clean option. Only Stove top burners worked
I began by turning off the breaker in the panel. Slide the oven out into the open area. Removed 3 screws in order to remove rear top panel. Took 2 pictures of the wiring location on the PCB Removed all wiring going to the circuit board total of 8. Removed 4 screws in order to remove bad PCB. Remove faceplate from bad PCB (you will need to place this faceplate on the new PCB.
Pull range away from back wall. Remove panel behind control knobs by removing the screws that hold it on. Find hot burner light that holds lens. Remove broken part of lens. Insert new lens into hole on front of control panel and into hot burner light receptacle. Replace back panel. Slide range back into place.
The part that was ordered based on the shamanic wasn't the part that was needed for the repair. It was to short. I took the other screw for the other side and that screw was an inch longer than the screw that was ordered thru your company. I then went too a jar that I placed extra screws, nuts and bolts which l keep in my garage . I found a same length screw but a different head and it works perfectly fine. When I ordered the part from your company most of the parts did not have a photo of the part on file, or a description like how long the part is. I still ordered it because it should fit the make and model number that was posted on the shamanic that was showed to me on line.