RAB4232EW1 Roper Washer - Instructions

I pulled the hose off and notice their was a part # and I went online and type the part # and showed the part and cost. I order it and receive it within 3days. when the part arrive I replace the hose in minutes. If I can do so can you its that easy.

researched the problem from the web-site.found the three most common things that would cause the problem.inspected the washer to see if there was evidence that one of the described parts had falled,and found that the tub wear pads were missing do to wear.simply replaced and it solved the problem. Thanks for the information.

Siphon break kit keeps washing machine from continuing to siphon after rinse/cycle -- like emptying a pool with a hose. Fixed the problem of the tub never filling due to siphon draining out water as it's being put in.

Pushed the new one into place. No tools, no fuss and very little swearing involved. Clogg was caused by erroneously pouring the liquid detergent into the very handy opening reserved for fabric softener. I'd love to say my wife did that, but.... no, it was me. NOW, the real story. I ordered the part via the web at 10:00 a.m. It was delivered to me at 9:30 a.m. the next morning via Fed Ex. Wow! Great job at PartSelect.

Watched the video and followed the instructions. Everything went smoothly and the repair was done in under 15 minutes, less time than it took to mop up the water when it overflowed telling me that there was a problem.

Sprayed wd40 - limescale - boiling water , NOTHING WORKED after half an hour reapeted spraying and pulling the tub and shaking it back and forth - still nothing
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job

The instructional video that was attached with the part I purchased was spot on with very simple instructions. The inlet valve came with a metal bracket that was not needed for my model, so just tossed it. Was completed with replacement in about 30 minutes with help from my aspiring handywoman wife (would have taken 15 minutes without her)

Clutch was noticibly worn compared to new part. Direct drive flange had broken, this part should be steel. found a you tube video that was simple to follow. no problems

I found the problem when I leaned on the lid while it started and that pressure kept it running. By placing detergent bottles on the right side of the lid I was able to walk away. I then bought the lid switch and lid strike after seeing it is a common problem. I watched the video and followed it almost step by step. First I unplugged the washer but didn't unhook the hose (only because I didn't have to move the washer) then I unscrewed the two screws holding the control panel, flipped it over, unplugged the lid switch connector, removed the clips holding the washer body on and tilted the body far enough forward to work on it. I replaced the switch as was done in the video and put the washer back together opposite the way I took it apart.

Replaced motor starting capacitor. Noticed water leak at pump and replaced pump

I removed the cabinet and agitator, layed the machine on it's back, removed the pump, motor and gearcase. I found a way to prop the gearcase up so it rested level, removed the cover, drained the old oil. I removed all internal parts, disassembled them and cleaned them. I reassembled the gearcase using the new uetral drain assembly, and replaced the oil. I made sure the brake assembly was pushed into position and then put the gearcase, motor and pump back in. I sttod the machine up, put the cabinet back on and tested the machine. It still did not spin, so it wasn't the coupler, clutch or nuetral drain assembly.

The video that was shown about how to perform the repair was spot on. I wasn't sure exactly what part I needed. I took the advise from you stating that these symptoms I described usually meant that the part I ordered was the correct repair In 65% of the cases. I was delighted to see that when I followed the instruction video, and the motor was removed, there was my coupling, In several pieces. At that point I knew that I ordered the correct parts.
Thank You,
Mario for Eastchester, NY.

to change it was 1,2,3
thank you guys

Direct drive, no belt. Motor sounds like it's spinning but the agitator is not. Bought the coupling (that goes between the motor and the transmission) and replaced it in less than 15 minutes. Two screws and two clips to open the cover. Two clips to move the water pump out of the way. Two screws and two clips to take out the motor. Replace the coupling and reverse the steps.

Followed direction that was sent to my e-mail. My washer timer would not advance. I' am so happy for the directions sent to me from this site and being able to get the part that I, needed from this site. I, didn't have and business doing the job myself, because I'm a ill 66 year old female. There's no special instructions that I, have to add. !! Thanks !! Lewis