Quick Question!

Have you ever purchased from PartSelect.com before?

Models > PHS68EJSB0 > Instructions

PHS68EJSB0 Frigidaire Refrigerator - Instructions

All installation instructions for PHS68EJSB0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the PHS68EJSB0
556-570 of 799
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

ice maker would not dispence ice

  • Customer: james from chatsworth, GA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
took ice maker out empty ice removed 6 screws removed auger out took off lcck nut pulled off drum replaced with new drum reassembled.

Very weak water pressure from dispenser, hollow ice cubes

  • Customer: Dominic from Key West, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
I diagnosed the problem by checking the water flow at the supply valve and hose by disconnecting the hose from the back of the fridge. Found the pressure to be adequate. I then reconnected the supply hose and removed the cardboard backing from the fridge and removed the nuts holding the water inlet valve to the chassis. I loosened the first hose that runs from the bottom of the valve and had my wife activate the valve by pushing the water switch on the front of the fridge. Water basically sputtered out of the valve and I decided that was where the problem was. I ordered the valve from partselect. When it arrived I thought it was the wrong part because it had push-fittings whereas my original valve was all thumb screws. I took a chance and one by one used a utility knife to cut the hose free of the old valve as close to the nut as possible. Connecting them to the new valve was a piece of cake! Just make sure the hose bottoms out when you push it in. I turned the water back on, no leaks! Plugged the fridge in and pushed it back to the wall. After a bit of air bled out I had a strong flow of wateragain like new! The next day the ice cubes were solid again! We use the filtered water so many times a day and had been so frustrated with the slow water flow we had considered donating the fridge and buying a new one; thanks to this easy fix we expect keep it for years to come!

Freezer side plastic door shelf bin was accidently broken.

  • Customer: William from Shreveport, LA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Upon receipt of replacement part I simply snapped it into place. More accurately, the "less than 15 mins" above was more like less than 15 seconds. Ordering this part was easy and clearly understood. I ordered about noon one day and received the FedEx shipment evening of the following day. Incredible! While somewhat pricey for what the part is I understand the costs associated with stocking minor parts and am totally happy with my whole shopping experience at PartSelect. I have already recommended PartSelect to others and have bookmarked the website for future reference as needed.

Ice door flapper broke in half

  • Customer: James from Atlantic, VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed a video I found on how to take the front off of the ice dispenser ( to me the hardest part) Once I was in there it was a matter of removing the pin and spring,then putting the new flapper in place of the old. Hardest part in reassembling was getting the spring back where it belongs. After that it was a matter of putting the ice dispenser back together and testing. Works perfectly.

The ice crusher housing is made of plastic and a piece of it broke off,

  • Customer: JAMES from COOSADA, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove 4 screws to get the housing cover off. Remove the lock ring that holds the ice auger in place. REmove 4 screws to get the crusher housing off. Reverse the order to replace the housing. Very simple.

hook broke

  • Customer: Larry from Lincoln, NE
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
just installed new shelf

Broken Shelf

  • Customer: Luis from Exton, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I ordered the part from PartSelect and the order was procesed promptly. I installed the shelf and everyting is back to normal. Thanks!

Water dripped from water dispenser after use

  • Customer: Jeffrey from Greenfield, MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Pulled fridge away from wall and unplugged. Turned off main water supply feed and removed fitting from water inlet valve. Took off back panel by removing 3 screws. Took out 2 screws holding valve to fridge. Pulled off color coded wire clips. Unscrewed each water tube connector. New valve had quick connectors so had to snip off flared ends of tubing with utility knife. Pushed tubing firmly into new valve fittings and pulled to ensure connection. Reattached wiring and reattached valve to fridge with the 2 screws. Reconnected water feed line and turned on main water feed. Checked for leaks before replacing back panel. Done. No more dripping from water dispenser.

Three of the four drawer supports were broken

  • Customer: Linda from Turtle Creek, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
It went okay. My husband did the job and he is handy. We both watched the little "How to" video and that was very helpful.

broken plastic bin

  • Customer: Rosemary from Belton, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I just popped the plastic bin right into place. It was so easy it took me less than 5 mins

Crisper support broke

  • Customer: Diana from Clearwater, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Had to pry the old one from the cabinet. Had to work remaining piece evenly as to not crack the cabinet of the fridge. Not the best design on Frigidaire's part but it was fixable. Thanks for stocking every part under the sun.

Broken shelf

  • Customer: James from Layton, UT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Removed old one inserted new one . 15 seconds was done

Broken side rails on meat storage drawer

  • Customer: Paul from North Haven, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed shelf and rails. Removed screws from the sides. Removed old broken rails. Mounted replacement rails and secured with screws. Mounted shelf back in refrigerator. Important!! Sanded down the rough edge of the original tray which had cut through the plastic rails. then I lubricated the sides with a small amount of lithium grease.Mounted the drawer and was incredibly impressed by the ease of operation!It is sooo smooth!

time to replace water filter

  • Customer: Judith from Hainesport, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
take out the old....put in the new...couldn't be easier!

Ice Maker stopped working

  • Customer: Charles from Fishkill, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Realized Ice Maker was not getting water during it's cycle and suspected water valve based on other posts to this web site. My fridge is 9 years old and the tubes connecting the valve were plastic screw on type. The new valve did not have threads to accept the nuts. Turns out all I had to do was cut the nuts off and insert the water tubes into the valve which auto-locked the tubes to the valve. Ice maker now works great.
All Instructions for the PHS68EJSB0
556-570 of 799