NGD7200TW10 Amana Dryer - Instructions

This was a simple repair. Removed the small access panel where the vent pipe comes through, the roller is right there. Unscrewed the support roller bolt, looking for all the pieces that had broken and fallen inside the housing of the dryer. Using the washers and nut from the old one, put the new roller in place, be aware that you have to lift the drum a little bit to get this new roller in. It could take two people depending on your strength. Tightened down the roller, spin the drum by hand to make sure it was ok, then put the access panel back on and fired it up for a test run.

I read some of the repairs of other people and this best described my situation. I ordered the Radiant Flame Sensor and followed the step by step instructions in the video for the repair, which by the way was excellent. It couldn't have been easier. My most difficult part of the repair was moving my dryer out of the laundry closet.

Remove lower bottom cover (two screws on bottom) with screw driver. Remove old radiant flame sensor from left side of tube with ignior by using socket wretch. Remove wires with needle nose pliers. Put new part in: put wires back on, insert part's lower tab into the tube ( there is a small slot) use socket wrench to tighten screw at top. Put bottom front panel back on and screw back in.

After reading other posts, I learned that "tO" meant that the thermistor was open. Also, I read that this part would bench test with a multimeter correctly but could still malfunction in the dryer. FIRST UNPLUG DRYER. After checking all of the exhaust ducting including inside the dryer for any blockages that could result in an overheating problem I decided to order a new thermistor. To replace thermistor: First, there are two screws at the rear top that you remove and the top tilts up and comes off. There are four screws on the top front that removes the front control panel. Next remove the screws at the top of the dryer, two screws in recesses behind the door and tilt front forward while unplugging the door switch. Lift and remove front with door attached. Remove screws from exhaust duct and slide down and out. Thoroughly clean inside of duct and fan blades. Clean out any other lint build up. Locate thermistor to the right of duct, unplug and remove two screws. Replace with new part and reassemble while not forgetting to plug the door switch back in. At the rear of dryer, remove screws around exhaust duct and remove. Dryer will have to be slid away from wall about three feet to remove duct from inside dryer. Clean thoroughly and check/clean and check for blockages in ducting from dryer to outdoors. Re assemble making sure rear duct engages the front ducting properly.Plug dryer back in and enjoy.

You know! I forgot exactly where it was i got the info to fix the problem but, "Parts select" was mentioned. Once I had an idea as to what to do I then, wasted time around town looking for the parts with no results. I then did what I should have at first an ordered the parts from Parts select. got them in the mail, lightning quick! I think I may have found the info here as well,not sure. (this site is awesome None the less) but the info led me to the Thermostat, I then jumped it as indicated and wham!! it ran. Order both the thermostat and thermistor. only problem I ran into was, removing the front display panel. broke some of the retaining clips off in the process. all in all, it was an easy fix that saved me a bunch of dough. greatfull to parts select for a speedy deliverie and to the website that made it possible. think it may have been here at the free repair help, section. awesome and highly recommended thanks!!!

Replace the igniter and dryer did light and after 3 minute went out. so I ordered to gas valve selenoid's and replaced those and everything it working properly

After getting on-line to your site we looked up what the problem could be after receiving the dryer from a friend to transfer from electric to gas to save money. First we thought it to be the ignitor and after receiving it so quickly it still didn't work so went to your site again and found the Flame sensor. They were both defective and now it works wonderful!!! Your site also explains what and how to repair the appliance, which my husband appreciated! We are glad you contacted us because your site did not show that we could send you and e-mail Thanking your company for the excellant service we received. Your prices can't compare to other companies either, we were amazed on the differences. When you say the next day delivery, you mean the next day!!! Thankyou and you are now in my Favorites if ever needing parts for other appliances we own.

Dryer was real easy to get into, there are two 1/4" screws on top back of dryer that you can take out to take off the top. The elec. control board is on the left front of mach. it takes about 2 or 3 mins. to take out with a screw driver. I suggest that you go ahead and pull front of dryer off and clean it out if possible as the inside of mine was full of lent. There are only 4 or 5 screws holding the front on, the door will come off with front cover. It is also very easy to check all the sensors and the heating element if you have a multi meter. I hope this will help Oscar

changed fuse,radiant flame sensor. no help. bought a new dryer. i don't think the gas valuve was opening.everything seemed to be working properly,just no gas.

Followed troubleshooting steps. Checked thermal fuse (shorted)- OK. Checked igniter (about 70 ohms) - OK. checked flame sensor - (open) BAD (should read shorted). This part is normally shorted then opens when the igniter gets hot causing it to open and thus turns on the gas flow. An open flame sensor does not permit the igniter to turn on.

The Maytag dryer had a removable front panel so it took only about 15 minutes to remove the front, replace the blocking plug and orifice and reinstall the front panel. I gave the repair time as 30-60 minutes since I took the time to vacuum the interior and clean the flame sensor. Great instructions were included with the kit.

after removing 2 screws securing top of dry i isolated the humming noise to the electronic board. Dryer would not turn on but drum light would work. 2 screws hold the electronic mount, and 1 screw hold electronic board. all electrical connection on board easily unplugged. connected new board installed in mount with 1 screw and then installed mount with two. plugged in and pressed power switch and electronic timer came up and dry started at the press of cycle start knob. the key to this repair was the stuck relay humming sound being generated by the either the relay or transformer on electronics control board.

The part came in very quickly. If you know how to remove the front panel, it is very easy to repair. The hard part is to diagnose the problem. The first thing to check is the igniter. If it comes on then you look for faulty limit switches. If you have lots of training in electronics and appliance repair this is very easy, if you do not I would not try this. I have 40 years in the repair business, It still took me 1hr. to find the problem. the switch was intermitted, one time the dryer would work the next time it would not. Good luck and happy repairs.

Unplugged dryer from power source, used putty knife to release latches that hold top on, tilted the top out of the way, unplugged door lite, located the radiant switch, removed 1 screw,then undid 2 wires & lifted out switch. Reversed procedure plugged in dryer....wa la had dried a large load of clothes, took 1/3 the time to dry clothes at last. Thanks "PartSelect"

I verified that the thermistor was bad by testing the resistance. My manual said it should be 10K ohms at 78F. I was reading over 30K ohms. This is what caused the thermostat to blow, as the thermistor was telling the dryer the air temp was a good 30 degrees cooler than it actually was. You can also verify the thermostat is bad by checking it for continuity. I removed the screws on the top-back of the dryer and slid the top back to reveal the screws holding on the control panel. I removed those and popped off the control panel. It required a good bit of force. I then removed the four screws holding the front piece on and removed it by pulling it slightly towards me and up. The parts are located on the bottom right. They were underneath a black plastic flap on my dryer. I removed the cables and the took both parts out with a screwdriver. I replaced them with the new ones (they should only fit in the right slot) and reattached the cables. From there, reassemble in reverse of the disassembly.